[ANSYS Meshing] ICEM Meshing :specified nodes along curve did not appear

syler3321 · June 13, 2012, 03:50

Hi,
Can anybody help me with this problem?
I'm creating a mesh for a weird airfoil using surface mesh. I can't use the blocking method in ICEM because the geometry is too complex. What I did was the following:
1. Create a surface of the whole domain.
2. Segment/trim the airfoil from the surface.
3. Delete the airfoil.
4. Go global mesh and set to patch dependent, tri;
5. Curve mesh setup, clicked the curves delineating my airfoil and set the number of nodes.
6. Compute mesh.

After that i found that my leading edge only consisted of 4 to 5 mesh nodes making it look rather clunky and not smooth. I specified at least 30 nodes in that region but somehow ICEM cannot seem to do this. What am i doing wrong?edge001.jpg

yonchong · June 13, 2012, 08:40

Try patch-independent option.

syler3321 · June 13, 2012, 15:36

hi yonchong,
I cant use patch independent because i'm trying to get a periodic boundary condition. I tried it already but ended up with a mesh that has no periodic boundaries ( even though i specified it). Also a patch independent mesh leaves big meshes within the domain.

yonchong · June 13, 2012, 15:45

Are you sure about the periodic boundary condition and patch independent? I thought it was the other way around. If you use patch dependent you will not have the periodic boundary condition because you are using the surface geometries to build a surface mesh.

The patch independent uses Octree Volume mesher and then delete the volume mesh when it finishes leaving only a surface mesh. In fact, you could do the Octree Volume meshing and then manually delete the volume mesh to have the surface mesh only. The periodic boundary condition should be there because you are building the volume mesh initially for this.

If I were you I will try again.

June 13, 2012, 03:50	ICEM Meshing :specified nodes along curve did not appear	#1
syler3321 Member ralph Join Date: Jun 2010 Location: Calgary Alberta Posts: 38 Rep Power: 15	Hi, Can anybody help me with this problem? I'm creating a mesh for a weird airfoil using surface mesh. I can't use the blocking method in ICEM because the geometry is too complex. What I did was the following: 1. Create a surface of the whole domain. 2. Segment/trim the airfoil from the surface. 3. Delete the airfoil. 4. Go global mesh and set to patch dependent, tri; 5. Curve mesh setup, clicked the curves delineating my airfoil and set the number of nodes. 6. Compute mesh. After that i found that my leading edge only consisted of 4 to 5 mesh nodes making it look rather clunky and not smooth. I specified at least 30 nodes in that region but somehow ICEM cannot seem to do this. What am i doing wrong?edge001.jpg

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ICEM] ICEM Hexa Meshing Automation	Haasini	ANSYS Meshing & Geometry	1	April 24, 2012 22:46
[ICEM] meshing issues in ICEM CFD	acjoshi	ANSYS Meshing & Geometry	3	April 14, 2012 12:01
[ICEM] Unstructure Meshing Around Imported Plot3D Structured Mesh ICEM	kawamatt2	ANSYS Meshing & Geometry	17	December 20, 2011 11:45
Meshing a Mixing Plane in ICEM	Will Anderson	ANSYS Meshing & Geometry	2	November 9, 2010 09:16
[ICEM] Need help in ICEM CFD Mapped Meshing	falconf16	ANSYS Meshing & Geometry	3	February 19, 2010 14:21

June 13, 2012, 08:40		#2
yonchong Member Yon Han Chong Join Date: Jun 2012 Posts: 77 Rep Power: 13	Try patch-independent option.

June 13, 2012, 15:36		#3
syler3321 Member ralph Join Date: Jun 2010 Location: Calgary Alberta Posts: 38 Rep Power: 15	hi yonchong, I cant use patch independent because i'm trying to get a periodic boundary condition. I tried it already but ended up with a mesh that has no periodic boundaries ( even though i specified it). Also a patch independent mesh leaves big meshes within the domain.

June 13, 2012, 15:45		#4
yonchong Member Yon Han Chong Join Date: Jun 2012 Posts: 77 Rep Power: 13	Are you sure about the periodic boundary condition and patch independent? I thought it was the other way around. If you use patch dependent you will not have the periodic boundary condition because you are using the surface geometries to build a surface mesh. The patch independent uses Octree Volume mesher and then delete the volume mesh when it finishes leaving only a surface mesh. In fact, you could do the Octree Volume meshing and then manually delete the volume mesh to have the surface mesh only. The periodic boundary condition should be there because you are building the volume mesh initially for this. If I were you I will try again.