 |
 |
 |
|
|
|
[Sponsors] | ||||
October 17, 2012, 07:11
|
merge surface mesh
|
#1 |
|
Member
hadrien calmet
Join Date: Nov 2011
Posts: 34
Rep Power: 14  |
Hi Guys
I have a new problem. I have a good stl and I want to merge some surface mesh with this stl to close the domain and use the total surface mesh to do a delaunay mesh. I send a picture. I was looking for in edit mesh > merge nodes but I don't found nothing. If you have a idea to do it ? Thanks |
|
|
|
|
|
October 18, 2012, 14:58
|
|
#2 |
|
Senior Member
Simon Pereira
Join Date: Mar 2009
Location: Ann Arbor, MI
Posts: 2,663
Blog Entries: 1
Rep Power: 47 |
You may be looking for the stitch edges command...
But an easier way to do it (assuming the purple surface is a mesh, or after you convert it to a mesh using Edit => Facets to Mesh) would be to close holes... Select one of the edges and flood fill (hot key "l") to select the others, then MMB. Best regards,
__________________
----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey |
|
|
|
|
|
|
October 19, 2012, 06:58
|
|
#3 |
|
Member
hadrien calmet
Join Date: Nov 2011
Posts: 34
Rep Power: 14 |
Hi PSYMN
I try to close holes using edit mesh > repair mesh > Flood fill/make consistent there is 2 option flood fill and make volume mesh .... I suppose that I have to toggle on flood fill you write "Select one of the edges and flood fill (hot key "l") to select the others, then MMB." but if I select only flood fill I can't select nothing and If I select both (flood fill and make volume....) I can select elements not edges and the key "i" doesn't work and last question what means MMB ? Sorry PSYMM, so many questions thank a lots |
|
|
|
|
|
|
October 19, 2012, 15:07
|
|
#5 |
|
Member
hadrien calmet
Join Date: Nov 2011
Posts: 34
Rep Power: 14 |
middle mouse button
of course !!!!!!!!! thank shine on crazy diamondx !!!!!!! |
|
|
|
|
|
|
October 19, 2012, 22:41
|
|
#6 |
|
Senior Member
Simon Pereira
Join Date: Mar 2009
Location: Ann Arbor, MI
Posts: 2,663
Blog Entries: 1
Rep Power: 47 |
I didn't mean to use the "Flood fill" command. you should use the "Repair => Mesh From Edges" Then select a single edge and then hit the hotkey "l" for flood fill. You could also pick flood fill from the selection tool box.
Best regards, Simon
__________________
----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey |
|
|
|
|
|
|
October 22, 2012, 05:24
|
|
#7 |
|
Member
hadrien calmet
Join Date: Nov 2011
Posts: 34
Rep Power: 14 |
thanks
It s work ! thank you guys !!!!!! |
|
|
|
|
|
 |
| Thread Tools | Search this Thread |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| [Gmsh] Problem with Gmsh | nishant_hull | OpenFOAM Meshing & Mesh Conversion | 23 | August 5, 2015 02:09 |
| [ICEM] Generating Mesh for STL Car in Windtunnel Simulation | tommymoose | ANSYS Meshing & Geometry | 48 | April 15, 2013 04:24 |
| [snappyHexMesh] Layers don't fully surround surface | EVBUCF | OpenFOAM Meshing & Mesh Conversion | 14 | August 20, 2012 04:31 |
| [Gmsh] 2D Mesh Generation Tutorial for GMSH | aeroslacker | OpenFOAM Meshing & Mesh Conversion | 12 | January 19, 2012 03:52 |
| fluent add additional zones for the mesh file | SSL | FLUENT | 2 | January 26, 2008 11:55 |
Linear Mode
