[ANSYS Meshing] How to create Quadrilateral mesh

b.shuvayan · October 29, 2012, 06:54

Hi everyone!

I was solving a problem in ANSYS (CFX fluid flow) work bench and found a problem. I created the geometry and after meshing I found that the system, creates by default the triangular mesh which has to be changed to quadrilateral mesh (as per my Project guide instructions)

. Can anyone please tell me how to change the triangular mesh to quadrilateral.

Any help would be appreciated.

Shuvayan Brahmachary
Asst. Project Engineer
Indian Institute of Technology, Guwahati
India

Far · October 29, 2012, 07:32

You need some working Design modeller to make the map mesh. However this task can be done more conveniently in ICEM

b.shuvayan · October 30, 2012, 06:34

But can it be done in CFX MESH itself?? If not than how can it be done in ICEM??

thanks for the advice

b.shuvayan · October 30, 2012, 07:06

Okay!.. I just converted the triangular mesh to quadrilateral mesh. But it turns out that ICEM now is little bit different from CFX MESH, and I'm not able to create the inflated layers as I did in CFX MESH. any suggestions???

hellsblade.91 · November 29, 2017, 17:55

hey bhuavn how did you manage to put quadrilateral elements

Jorkoslav · November 30, 2017, 05:23

Hi Shuvayan!

Here you can see more about meshing.

October 29, 2012, 06:54	How to create Quadrilateral mesh	#1
b.shuvayan Member Shuvayan Brahmachary Join Date: Oct 2012 Posts: 36 Rep Power: 13	Hi everyone! I was solving a problem in ANSYS (CFX fluid flow) work bench and found a problem. I created the geometry and after meshing I found that the system, creates by default the triangular mesh which has to be changed to quadrilateral mesh (as per my Project guide instructions). Can anyone please tell me how to change the triangular mesh to quadrilateral. Any help would be appreciated. Shuvayan Brahmachary Asst. Project Engineer Indian Institute of Technology, Guwahati India

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Gambit problems	Althea	FLUENT	22	January 4, 2017 03:19
[snappyHexMesh] Layers:problem with curvature	giulio.topazio	OpenFOAM Meshing & Mesh Conversion	10	August 22, 2012 09:03
How to create a mesh use ICEM in CFX?	little stone	CFX	3	July 17, 2012 19:33
[ICEM] Problem making structural mesh on a surface	froztbear	ANSYS Meshing & Geometry	1	November 10, 2011 08:52
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 11:55

October 29, 2012, 07:32		#2
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	You need some working Design modeller to make the map mesh. However this task can be done more conveniently in ICEM

October 30, 2012, 06:34		#3
b.shuvayan Member Shuvayan Brahmachary Join Date: Oct 2012 Posts: 36 Rep Power: 13	But can it be done in CFX MESH itself?? If not than how can it be done in ICEM?? thanks for the advice

October 30, 2012, 07:06		#4
b.shuvayan Member Shuvayan Brahmachary Join Date: Oct 2012 Posts: 36 Rep Power: 13	Okay!.. I just converted the triangular mesh to quadrilateral mesh. But it turns out that ICEM now is little bit different from CFX MESH, and I'm not able to create the inflated layers as I did in CFX MESH. any suggestions???

November 29, 2017, 17:55		#5
hellsblade.91 Member Hells Blade Join Date: Nov 2017 Posts: 61 Rep Power: 8	hey bhuavn how did you manage to put quadrilateral elements

November 30, 2017, 05:23		#6
Jorkoslav New Member Georgi Panchev Join Date: Dec 2016 Location: Bulgaria Posts: 5 Rep Power: 9	Hi Shuvayan! Here you can see more about meshing.