[ICEM] merging two type meshes

feizaghaee · June 20, 2013, 18:49

hi all. I'm meshing a channel. but I can't merge the in the interface. I attached a picture of these two meshes. I was wondering if somebody help me.

diamondx · June 20, 2013, 21:18

merging two meshes works only for 3d... can you block everything ???

feizaghaee · June 21, 2013, 09:33

the mesh on the left hand was generated by blocking and in right part mesh was generated by extrusion of quad dominant surface mesh. I found that the interface between two type of meshes doesn't include any nodes of meshes. when i use tetra mesh instead of extrusion of surface mesh nodes of tetra mesh are located on the interface but nodes of hexa meshes aren't.
how can I place nodes on the interface to merge the?
thanks in advance

diamondx · June 21, 2013, 15:31

under the edit mesh tab, there is an icon for merge nodes, but then again i don't recommend that method. why don't you block everything

feizaghaee · June 22, 2013, 10:55

Quote:

Originally Posted by diamondx

under the edit mesh tab, there is an icon for merge nodes, but then again i don't recommend that method. why don't you block everything

thanks for your reply. only nodes of right part of the mesh are located in the interface. I can't merge nodes. I don't block everything because of geometry. the weir in this channel has various curvature radius. if I want to block everything, should I use multiblock?

Far · June 23, 2013, 02:59

Not multiblock!!! Simple hexa blocking will do the job. It should not difficult to make the blocking for 2d case.

feizaghaee · June 23, 2013, 04:42

thanks Far. I made a big mistake. I solved it.thanks a lot.

Far · June 23, 2013, 04:55

mistake related to merging? how did you solve it?

feizaghaee · June 24, 2013, 15:59

Yes. It was related to merging. I didn't create body in both side of interface.

June 20, 2013, 21:18		#2
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	merging two meshes works only for 3d... can you block everything ??? __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

June 21, 2013, 15:31		#4
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	under the edit mesh tab, there is an icon for merge nodes, but then again i don't recommend that method. why don't you block everything __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

June 23, 2013, 02:59		#6
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	Not multiblock!!! Simple hexa blocking will do the job. It should not difficult to make the blocking for 2d case. feizaghaee likes this.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[CGNS] CGNS converters available	mbeaudoin	OpenFOAM Meshing & Mesh Conversion	137	December 14, 2018 04:20
Temperature Issue in OpenFOAM-2.2.0	prasant	OpenFOAM	0	March 12, 2013 07:17
[swak4Foam] Air Conditioned room groovyBC	Sebaj	OpenFOAM Community Contributions	7	October 31, 2012 14:16
[Commercial meshers] Using starToFoam	clo	OpenFOAM Meshing & Mesh Conversion	33	September 26, 2012 04:04
Problems with Turbulence Modeling	ezsoal	OpenFOAM Running, Solving & CFD	4	November 26, 2009 15:12

June 21, 2013, 09:33		#3
feizaghaee Senior Member moein Join Date: Dec 2009 Posts: 132 Rep Power: 16	the mesh on the left hand was generated by blocking and in right part mesh was generated by extrusion of quad dominant surface mesh. I found that the interface between two type of meshes doesn't include any nodes of meshes. when i use tetra mesh instead of extrusion of surface mesh nodes of tetra mesh are located on the interface but nodes of hexa meshes aren't. how can I place nodes on the interface to merge the? thanks in advance

June 23, 2013, 04:42		#7
feizaghaee Senior Member moein Join Date: Dec 2009 Posts: 132 Rep Power: 16	thanks Far. I made a big mistake. I solved it.thanks a lot.

June 23, 2013, 04:55		#8
Far Super Moderator Sijal Join Date: Mar 2009 Location: Islamabad Posts: 4,553 Blog Entries: 6 Rep Power: 54	mistake related to merging? how did you solve it?

June 24, 2013, 15:59		#9
feizaghaee Senior Member moein Join Date: Dec 2009 Posts: 132 Rep Power: 16	Yes. It was related to merging. I didn't create body in both side of interface.