CFD Online URL
[Sponsors]
Home > Forums > ANSYS Meshing & Geometry

[ANSYS Meshing] pipe

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   July 30, 2013, 13:58
Default pipe
  #1
New Member
 
Pawel
Join Date: May 2013
Posts: 11
Rep Power: 3
pawel_sag is on a distinguished road
hello,
i am new to cfd.
can someone help me? is this proper mesh? or should i change something?
thx a lot for help.
Attached Images
File Type: jpg 1.jpg (80.5 KB, 12 views)
File Type: jpg 2.jpg (82.8 KB, 17 views)
File Type: jpg 3.jpg (46.7 KB, 19 views)
File Type: jpg 4.jpg (39.1 KB, 12 views)
pawel_sag is offline   Reply With Quote

Old   August 6, 2013, 09:18
Default
  #2
Senior Member
 
Paritosh Vasava
Join Date: Oct 2012
Location: Lappeenranta, Finland
Posts: 463
Rep Power: 12
vasava will become famous soon enough
Although it looks good, it depends on what you want to simulate.
vasava is offline   Reply With Quote

Old   August 6, 2013, 12:15
Default
  #3
New Member
 
Pawel
Join Date: May 2013
Posts: 11
Rep Power: 3
pawel_sag is on a distinguished road
hello, i try to simulate swirl velocity. I made measurements on real models. now i am trying to simulate this.
pawel_sag is offline   Reply With Quote

Old   August 7, 2013, 04:00
Default
  #4
Senior Member
 
Paritosh Vasava
Join Date: Oct 2012
Location: Lappeenranta, Finland
Posts: 463
Rep Power: 12
vasava will become famous soon enough
Most of your wedge elements (the ones in the boundary layer) seem to be of low quality. You can try to improve by playing with mesh size.

Also you can run a test example with your mesh. If the 'viscosity limited' error persists then you may have to further refine your mesh. Remember the 'viscosity limited' error is ok/tolerable in the beginning of the simulation (say first few time steps or iterations) but not later than that.
vasava is offline   Reply With Quote

Old   August 18, 2013, 12:51
Default
  #5
New Member
 
Pawel
Join Date: May 2013
Posts: 11
Rep Power: 3
pawel_sag is on a distinguished road
i still get problems with this profile. i try different kind of mesh, but always simulation results are incorrect.
can you look on my profile i give me some advice?
http://www.speedyshare.com/hbxTP/Geomnorm.agdb
thx a lot for help
pawel_sag is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Double Walled Pipe Boundary dahvqaz FLUENT 2 December 5, 2012 11:14
[DesignModeler] DesignModeler Pipe within pipe shields ANSYS Meshing & Geometry 8 March 7, 2011 13:24
pipe in pipe heat exchanger JohannV FLUENT 3 December 3, 2009 03:53
My Revised "Time Vs Energy" Article For Review Abhi Main CFD Forum 2 July 9, 2002 10:08
Terrible Mistake In Fluid Dynamics History Abhi Main CFD Forum 12 July 8, 2002 10:11


All times are GMT -4. The time now is 23:36.