[ICEM] help! how to mesh a volute of the centrifugal compressor??

Aysiyi · December 23, 2013, 21:56

hi:
everyone ,now i have a geometry file ,it is a volute of a centrifugal compressor. i have tried many ways to mesh t ,but failed .i attach the file , i hope some expert can help me . it is a challegen for icem to mesh this type of structure.
the attachment is the geometry file of the volute. because of the limit of the the forums , you need to change the suffix from .zip to .rar ! .

thanks for suggestions . we can shares the experience ,learning each other.

raghav · January 9, 2014, 10:03

Hi,
I have attached meshed file for your geometry in the dropbox.
https://www.dropbox.com/s/vvp2tbuafa3qhab/Volute_Shared.zip

I have puffed the geometry with blocks and its not of that great quality I got.
In critical junction I have used blocks in a haphazard way.

Let me know if you come across any better blocking strategy. It will be helpful.

Regards,
Raghav

diamondx · January 24, 2014, 08:31

hey raghav,
The blocking you used is complex, but very good. good job.
It was discussed before that in critical junction, quality of the structured mesh can be very limited and there is nothing you can do about it.
I wanna try something on this, but I'm quit busy these days, I would love to try simon's trick to block the essential 2D surface (shown in the picture below) ; then extrude it along the curves, that would be certainly my move strategy:

Anyway your blocking is very good !

raghav · January 25, 2014, 06:20

thanks ali

will be longing to see further works on this from any of you guys

Regards,
Raghav

MDSHUJAN · November 13, 2018, 15:50

Raghav. Great work. It seems that you are an expert in ICEM CFD. I am trying to learn to mesh an centrifugal pump impeller in ICEM CFD. Please, would you attach a file showing meshing of any impeller?

MDSHUJAN · November 13, 2018, 15:53

Quote:

Originally Posted by raghav

thanks ali

will be longing to see further works on this from any of you guys

Regards,
Raghav

Raghav. Great work. It seems that you are an expert in ICEM CFD. I am trying to learn to mesh an centrifugal pump impeller in ICEM CFD. Please, would you attach a file showing meshing of any impeller?

January 24, 2014, 08:31		#3
diamondx Super Moderator Ghazlani M. Ali Join Date: May 2011 Location: Tokyo, Japan Posts: 1,385 Blog Entries: 23 Rep Power: 28	hey raghav, The blocking you used is complex, but very good. good job. It was discussed before that in critical junction, quality of the structured mesh can be very limited and there is nothing you can do about it. I wanna try something on this, but I'm quit busy these days, I would love to try simon's trick to block the essential 2D surface (shown in the picture below) ; then extrude it along the curves, that would be certainly my move strategy: Anyway your blocking is very good ! __________________ Regards, New to ICEM CFD, try this document --> https://goo.gl/KAOIwm Ali

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
help ! centrifugal compressor stimulation	Aysiyi	CFX	6	October 14, 2013 05:42
[Gmsh] 2D Mesh Generation Tutorial for GMSH	aeroslacker	OpenFOAM Meshing & Mesh Conversion	12	January 19, 2012 03:52
[ICEM] Unstructure Meshing Around Imported Plot3D Structured Mesh ICEM	kawamatt2	ANSYS Meshing & Geometry	17	December 20, 2011 11:45
CFD analysis of Centrifugal compressor	murthy pnvr	CFX	3	November 12, 2010 11:13
Centrifugal compressor volute	Stuman	CFX	2	November 29, 2005 00:25

January 25, 2014, 06:20		#4
raghav Member Raghav Join Date: Jul 2010 Location: India, Karnataka Posts: 47 Rep Power: 17	thanks ali will be longing to see further works on this from any of you guys Regards, Raghav

November 13, 2018, 15:50		#5
MDSHUJAN New Member SHUJAN Join Date: Jun 2016 Posts: 17 Rep Power: 9	Raghav. Great work. It seems that you are an expert in ICEM CFD. I am trying to learn to mesh an centrifugal pump impeller in ICEM CFD. Please, would you attach a file showing meshing of any impeller?