|
[Sponsors] |
December 1, 2011, 10:55 |
Problem with uniting volumes
|
#1 |
Senior Member
Join Date: Feb 2011
Posts: 140
Rep Power: 15 |
Dear all,
I have got a problem with uniting two volumes (using Gambit) which I generated via “Sweep Faces” (see pic). If I try to unite them I always get an error message: “ACIS error 8030: inconsistent face-body relationships”. Is there any way how I can avoid this? Thanks a million in advance! WBR Lilly |
|
December 2, 2011, 01:31 |
|
#2 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
can you provide your dbs file? (delete the mesh)
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
January 11, 2012, 05:01 |
Same problem in uniting volumes
|
#3 |
New Member
B.Krishna Chaitanya Reddy
Join Date: Jan 2012
Posts: 2
Rep Power: 0 |
Hi all,
I am facing a similar problem while uniting the volumes(in gambit) that are previously subtracted. The error message shows "ACIS error 8030: inconsistent face-body relationships". I want to unite all the volumes(all blades,volumes above and below the blades) and subtract it from another bigger volume(not in picture) Kindly help me to fix the issue....Thanx in advance Last edited by kc_reddy; January 15, 2012 at 08:50. |
|
January 11, 2012, 05:14 |
|
#4 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
be sure your volumes are fully intersected together.
you can unite volumes, one by one, and check which is giving you trouble
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
January 11, 2012, 12:23 |
|
#5 |
New Member
B.Krishna Chaitanya Reddy
Join Date: Jan 2012
Posts: 2
Rep Power: 0 |
Thanx for the suggestion once again.
The blades in my previous post were touching the top and bottom volumes. This time I extended them so that blades and the other two volumes intersect(uniting will anyway make them into one single volume). But even this time i got the same error message "ACIS error 8030: inconsistent face-body relationships". Another way: As i said there is another bigger volume which subtracts this entire geometry(after uniting). When I tried to first subtract just blades from this bigger volume was successful. But again while uniting resulted volume with top and bottom volumes, error appeared "ACIS error 8033: decision to delete intersection graph was incorrect". Please kindly help me. Thanx |
|
April 10, 2012, 15:54 |
Subtracting volumes
|
#6 |
New Member
Mbu
Join Date: Apr 2012
Posts: 1
Rep Power: 0 |
Hi, did you figure out how to fix the problem? I am getting
"ACIS error 8033: decision to delete intersection graphs was incorrect" when I try to subtract volumes in gambit. |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
problem importing mesh into gambit | tsm554 | FLUENT | 7 | December 3, 2010 22:15 |
Can I solve this problem by Fluent? | Kai_kc | FLUENT | 1 | October 27, 2010 05:29 |
Adiabatic and Rotating wall (Convection problem) | ParodDav | CFX | 5 | April 29, 2007 19:13 |
gambit error uniting two volumes | Ralf Schmidt | FLUENT | 3 | January 30, 2006 08:51 |
problem in CFX solver about isolated volumes | Yuan | CFX | 2 | August 16, 2004 22:54 |