|
[Sponsors] |
March 1, 2010, 05:57 |
error in gambit
|
#1 |
Member
Join Date: Oct 2009
Location: Italy
Posts: 88
Rep Power: 16 |
Hi
I have a problem, when i go to mesh a cylinder gambit show me this error: projection intervall count for periodic submap of face must be bigger than zero. what does it mean? thanks for the attention |
|
March 2, 2010, 01:14 |
|
#2 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
are you setting an interval count (number of nodes) instead of interval size?
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
March 2, 2010, 03:04 |
|
#3 |
Member
Join Date: Oct 2009
Location: Italy
Posts: 88
Rep Power: 16 |
i used an interval count (number of nodes) in the edge. thanks for reply and i would ask you if the following way is correct. i have split the cylinder in other so i can do the mesh.
however how can resolve the problem if it occurs in the future? |
|
March 2, 2010, 03:55 |
|
#4 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
what value did you gave for number of nodes?
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
March 2, 2010, 04:09 |
|
#5 |
Member
Join Date: Oct 2009
Location: Italy
Posts: 88
Rep Power: 16 |
i have given 14 nodes.
i have another problem when i go to mesh the side surface of a cylinder the mesh rotate how can i do to have a linear mesh? |
|
March 2, 2010, 05:01 |
|
#6 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
the message prompted from gambit sounds like you gave a negative value, or something weird.
post a picture for the other problem
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
March 2, 2010, 09:19 |
|
#7 |
Member
Join Date: Oct 2009
Location: Italy
Posts: 88
Rep Power: 16 |
this is the effect of the mesh
|
|
March 3, 2010, 01:12 |
|
#8 |
Super Moderator
Maxime Perelli
Join Date: Mar 2009
Location: Switzerland
Posts: 3,297
Rep Power: 41 |
Mesh your cap with pave-schema
__________________
In memory of my friend Hervé: CFD engineer & freerider |
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Gambit help: Cube inside cube | Jack Martinez | FLUENT | 13 | August 11, 2010 06:29 |
Gambit 2.3.16, Xming or Exceed...HELP! | bambam3417 | FLUENT | 10 | May 7, 2010 12:39 |
Does Gambit has a maximum allowable grid number? | spartan1516 | ANSYS Meshing & Geometry | 7 | March 25, 2010 09:08 |
Gambit -dev X11 doesn't work | Ervin Amet | FLUENT | 0 | October 28, 2007 08:33 |
Gambit batch - kill "Startup" box how? | Chris Bailey | FLUENT | 2 | February 23, 2005 09:05 |