Ahmed Body 3D mesh
 

Hi,

I am working on Ahmed Body.
Can somebody send me ahmed body mesh in 3D at samahmedpk2000@hotmail.com.

Dimension are attached here.

Ill be very thankful to you.

Regards,
Saima

I have completed AHmed Body 3D meshing I cant upload here because size is moore then 100KB, if somebody needs send me his/her email ill send it.

Can I have your completed meshed Ahmed body please?


Thank you.

ahmed body geo/mesh needed
 

Hi saima please I need the ahmed body geometry/mesh for my term paper kindly send it to abdels2005@yahoo.com. Thanks

Mesh Specifics
 

Is your mesh structured/unstructured? What mesh program did you use to create the domain? How many cells did you end up with? I am planning on running a similar simulation and would be glad for some mesh pointers.

Hi all!! I'm looking for the gambit ahmed body mesh too for my master thesis. I was wondering if anyone could send it to me at my e-mail: huidos60@hotmail.com. I will be very grateful!!

Can you please send me the mesh file? My email id is vs.vikramsngh91@gmail.com. It would be a big help.

Hi every body
I am working on Ahmed Body.
Can somebody send me ahmed body 3D model at javad.rahro@yahoo.com?
I'll be very thankful to you.

Regards,
javad.rahro

If you have access to ICEM, you can use following ready to use meshes. I assure you that with these meshes, you will always get the finest quality results.

http://www.cfd-online.com/Forums/ans...ured-mesh.html

http://www.cfd-online.com/Forums/ans...h-quality.html

ahmed body
 

hi saima
this is my mail id : parthiv.shah22@gmail.com
can u pls send me whatever u did on ahmed body.
thanks & regards
Parthiv shah

Ahmed body mesh
 

hi saima
I would really appreciate it if you could send me the mesh of the body with the smae geometries as stated above this is my mail id : pouya.1992@@gmail.com

Regards
Pouya Enayat

Hi saima please I need the ahmed body geometry/mesh for my project kindly send it to phil-12@live.co.uk. Thanks

Phil, I have sent u this.

hello,
I am a new member in this forum. I'm currently working in an experimental project on ahmed body. I'm having trouble how to make the make the front of it. Can someone help me with this problem? Your opinion will be much obliged.

Hi Saima,

Can you please send me the mesh you created. My email is sumit_279@hotmail.com

Many thanks.

Ahmed body mesh
 

Hi all,
I've seen this topic concerning Ahmed Body. I'm actually working on it during my internship for my master’s degree. Would one of you be nice by sending me the 3D mesh at orsini.adrien@gmail.com . (In fact will have to learn how to use openfoam practicing with the Ahmed body case, but I've just 3 days for that so it's gona be tough !). Is it possible to change/work on the mesh (that somebody will send me I hope !) after or not ?
Thanks a lot.
Adrien

Hello, can someone send me the mesh file for ahmed body. email: f2013489@hyderabad.bits-pilani.ac.in

Hello Saima, I dont mean to bother you and I hope this message meets you well, I would appreciate being sent the meshes for the Ahmed body 25 and 35 degree slant angles my email address is: amadichieloka@gmail.com
Secondly, i would like to seek your advice with regards to the experimental set-up, I am working on a suction and blowing project, and i am confused as to how to set up these additional velocities at the rear of the vehicle.
Looking forward to your reply.
with regards.

Ahmed body mesh
 

Hi Saima,

Could you please send me the mesh you created. My email is xuliangyu.1989@gmail.com

Thanks very much!

Ahmed body mesh
 

Hi...can anyone send me the meshed ahmed body

my mail id : jeelaravikumar@gmail.com

Thank you