CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > ANSYS Meshing & Geometry

repair the geometry in the ANSYS-ICEM

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   March 25, 2010, 10:07
Default repair the geometry in the ANSYS-ICEM
  #1
New Member
 
liuhuan
Join Date: Dec 2009
Posts: 13
Rep Power: 7
feixiangniao is on a distinguished road
Hello everybody.
When i want to mesh a assembly geometry by use of the ANSYS-ICEM, i firstly repair the geometry. so the gemoetry is as follows and the bule lines is not good .
SO do i must repair the blue lines ?
Attached Images
File Type: jpg 23.jpg (14.9 KB, 59 views)
File Type: jpg 2323.jpg (89.3 KB, 101 views)
feixiangniao is offline   Reply With Quote

Old   March 26, 2010, 07:52
Default
  #2
New Member
 
liuhuan
Join Date: Dec 2009
Posts: 13
Rep Power: 7
feixiangniao is on a distinguished road
who can help me ?
feixiangniao is offline   Reply With Quote

Old   March 26, 2010, 14:58
Default T Connections.
  #3
Senior Member
 
PSYMN's Avatar
 
Simon Pereira
Join Date: Mar 2009
Location: Ann Arbor, MI
Posts: 2,662
Blog Entries: 1
Rep Power: 35
PSYMN has a spectacular aura aboutPSYMN has a spectacular aura about
Blue lines just means "multiple edges". Basically, there are "more than 2" edges within the topology tolerance of that edge. It removes the others and keeps just 1. It may be fine if that is what you were expecting... It looks like you have walls that "T" connect with the surface. In which case, blue edges are fine (the three surfaces meet along the blue edge).

There are certain solvers that can't handle multiple edge T connections, but major commercial solvers don't mind at all.

Another possibility is that you have a thin surface and it is collapsing it along the surface to get the blue line... This is not what you want. If this is the case, measure to see what your smallest surface size is (that you want to capture), then reduce your topo tolerance to below this and try again.

Blue lines are a warning to look closer and make sure they are where they should be.

Best regards,

Simon
PSYMN is offline   Reply With Quote

Old   March 31, 2010, 05:53
Default
  #4
New Member
 
liuhuan
Join Date: Dec 2009
Posts: 13
Rep Power: 7
feixiangniao is on a distinguished road
Thanks sir Simon for your reply !
feixiangniao is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
How to open Icem mesh in Ansys Fluent? emmkell FLUENT 26 June 9, 2015 15:38
[ICEM] what does the different ANSYS ICEM and ANSYS Workbench? agungwp ANSYS Meshing & Geometry 7 October 27, 2014 21:12
help, ICEM mesh export to ANSYS Fred CFX 3 June 28, 2007 13:51
How to do Geometry from 3D mesh in ICEM San24 Main CFD Forum 4 August 8, 2005 02:49
Problem importing GAMBIT mesh to Ansys geometry David G. CFX 0 June 19, 2005 06:01


All times are GMT -4. The time now is 01:35.