CFD Online Discussion Forums

CFD Online Discussion Forums (http://www.cfd-online.com/Forums/)
-   ANSYS Meshing & Geometry (http://www.cfd-online.com/Forums/ansys-meshing/)
-   -   [Other] in cylinder.msh (http://www.cfd-online.com/Forums/ansys-meshing/84714-cylinder-msh.html)

aimandoul February 7, 2011 09:14

in cylinder.msh
 
I want to try the tutorial of fluent 6.3.26 for cold flow internal combustion engine.however i do not know where to find the in cylinder.msh file.can anyone help me?my email is raul_manestro@yahoo.com

ark April 1, 2011 17:06

Files sent to mail
 
I have sent those files to your mail.

asaleghahreman April 8, 2011 16:06

I made a cylinder in gambit,I put the circle face of this cylinder as inflow and the other circle outflow.but when
I put it in fluent and start it,it gives me floating point error.without any iteration.what is the problem?who knows?

ark April 8, 2011 16:11

download the cylinder files required for the tutorial from these links.. you ll need both.

in_cylinder.msh http://rapidshare.com/files/456518892/In_cylinder.msh
valve.prof http://rapidshare.com/files/456518893/valve.prof

asaleghahreman April 8, 2011 16:20

thank u for ur files,I want a case file to run in fluent??a pipe

ark April 8, 2011 16:23

For the cylinder tutorial, i have made the case and data files from the above 2 files.. i am sharing it here(below)

case file http://rapidshare.com/files/456520250/In_cylinder.cas
data file http://rapidshare.com/files/456520251/In_cylinder.dat

asaleghahreman April 8, 2011 16:31

thank u but I really need a 3D pipe,if u will share it,I would be happy..

ark April 8, 2011 16:32

sorry , dont have tht :(

Chavagnatze April 21, 2011 11:23

Quote:

Originally Posted by ark (Post 302832)
download the cylinder files required for the tutorial from these links.. you ll need both.

in_cylinder.msh http://rapidshare.com/files/456518892/In_cylinder.msh
valve.prof http://rapidshare.com/files/456518893/valve.prof

Rapid share wont allow me to download the mesh file. Can you email it to me please?

Thanks,
kmorse13@georgiasouthern.edu

minhtuan270183 May 12, 2011 22:17

Rapid share wont allow me to download the .msh and .prof file. Can you sent it to me please?

Thanks,
my email is minhtuan270183@yahoo.com

ark May 13, 2011 12:16

files have been sent ..

minhtuan270183 May 13, 2011 23:12

thank you very much

Ghalebsater June 12, 2011 14:58

Hello,

I really appresiate if you can send me the .msh and .prof files to my email g_Sater@hotmail.com . I couldnot download them from rapidshare.

Thank you.

Ghaleb

ark June 16, 2011 13:29

i have uploaded all the files needed for tht tutorial in mediafire. below is the link

http://www.mediafire.com/?6788sus7dcnd2

m_izadi October 10, 2011 04:12

sending In cylinder.msh
 
Hi

I couldnt download In cylinder.msh and also .prof . Its my Email.address: izadi.n@hotmail.com . Could you please send me files.

Kind regards,
M. Izadi

mir_ekk November 4, 2011 17:37

In-cylinder.msh
 
Hello,

I can say, that the link from ARK (http://www.mediafire.com/?6788sus7dcnd2) works properly,
really appreciate it,
Thanks!

M.S

reza6767 November 12, 2011 07:42

Quote:

Originally Posted by ark (Post 302832)
download the cylinder files required for the tutorial from these links.. you ll need both.

in_cylinder.msh http://rapidshare.com/files/456518892/In_cylinder.msh
valve.prof http://rapidshare.com/files/456518893/valve.prof

hi
this file unavailaible
can you send this file for me?
rezaamini6767@gmail.com
thank you!

ac_ankit May 3, 2012 13:16

In-cylinder.msh
 
:confused:
Quote:

For the cylinder tutorial, i have made the case and data files from the above 2 files.. i am sharing it here(below)
I am unable to get the results like velocity contours, pressure contours etc at angles other than 360 degrees through these case and data files. Any help is appreciated. Thanks

wind.cfd May 12, 2012 21:58

Hi,
I want to mesh the narrow elliptical cylinder, with r1=3 mm and r2=1/3 mm to simulate the flow in this cylinder.
I have a problem in generating the good mesh in the edge of this oval. To solve this problem I used the sizing function in gambit but still I cannot get the volume mesh. I would really appreciated if someone help me.

Thanks

ishwarmara November 8, 2012 06:06

thanks a lot i could download .msh and .prof files successfully...... i m trying to simulate it in fluent 13...i m getting an error, saying that; "Cannot change exhaust-seat-ob to wall.
Cannot change type of interface zone used in non-conformal interface".
Please help


All times are GMT -4. The time now is 14:52.