Tgrid left-handed face

me3840 · March 5, 2011, 23:20

When I run Tgrid, during prism generation, I run into an error where some element has a left-handed face. What does that mean?

Also, is there any way to use the display>grid to show me where the faces are that Tgrid referrs to with it's numbering system? Like, how do I know which face is face bf8886117?

Is there a 64-bit version of Tgrid?

Thanks.

me3840 · March 6, 2011, 15:31

Well, I found out that my edge lengths were less than the first height, which can generate this message. Changing the first height and increasing the number of layers can work.

But I still don't know how to display it - when I check left-handed in the display menu, nothing comes up. Is this because Tgrid removed the last bad layer? How can I tell where they are, then?

sandeep_tu · March 7, 2011, 07:28

1. Well, If you want to display a boundary face (bfxxxxxxxx) just go to
Boundary--->Modify----> and then click "face" in "Filter" tab and then type bfxxxxxxx (what ever number) in "enter selection" tab and then press enter, and then if you want to view it go to display---->grid---->faces select all "face zones" but don´t select any thing in "options" and then click "display" you will see the boundary face which you have typed.

2. I think tgrid is same for both 32 and 64 versions.

me3840 · March 7, 2011, 11:53

Thanks for the help on the view portion.

I don't think tgrid is the same though - I've run into an "out of memory" error with large meshes. I have 12GB of RAM, so..

udayrg · May 13, 2011, 07:37

One more way to locate the region would be

put in the desired face node or zone name in the display panel range set a small range and you would see it in the range you have set. i.e. local view...........

The 32 bit and 64 bit would be much more same as far as the source code is concerned

The Malloc error might occur as your hardware is insufficient to handle the mesh count that's being generated.

March 5, 2011, 23:20	Tgrid left-handed face	#1
me3840 Senior Member Join Date: Nov 2010 Location: USA Posts: 1,232 Rep Power: 24	When I run Tgrid, during prism generation, I run into an error where some element has a left-handed face. What does that mean? Also, is there any way to use the display>grid to show me where the faces are that Tgrid referrs to with it's numbering system? Like, how do I know which face is face bf8886117? Is there a 64-bit version of Tgrid? Thanks.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Netgen] Import netgen mesh to OpenFOAM	hsieh	OpenFOAM Meshing & Mesh Conversion	32	September 13, 2011 05:50
[blockMesh] BlockMeshmergePatchPairs	hjasak	OpenFOAM Meshing & Mesh Conversion	11	August 15, 2008 07:36
fluent add additional zones for the mesh file	SSL	FLUENT	2	January 26, 2008 11:55
[blockMesh] Axisymmetrical mesh	Rasmus Gjesing (Gjesing)	OpenFOAM Meshing & Mesh Conversion	10	April 2, 2007 14:00
[Commercial meshers] Trimmed cell and embedded refinement mesh conversion issues	michele	OpenFOAM Meshing & Mesh Conversion	2	July 15, 2005 04:15

March 6, 2011, 15:31		#2
me3840 Senior Member Join Date: Nov 2010 Location: USA Posts: 1,232 Rep Power: 24	Well, I found out that my edge lengths were less than the first height, which can generate this message. Changing the first height and increasing the number of layers can work. But I still don't know how to display it - when I check left-handed in the display menu, nothing comes up. Is this because Tgrid removed the last bad layer? How can I tell where they are, then?

March 7, 2011, 07:28		#3
sandeep_tu Member Sandeep Join Date: Apr 2009 Location: Munich, Germany Posts: 30 Rep Power: 17	1. Well, If you want to display a boundary face (bfxxxxxxxx) just go to Boundary--->Modify----> and then click "face" in "Filter" tab and then type bfxxxxxxx (what ever number) in "enter selection" tab and then press enter, and then if you want to view it go to display---->grid---->faces select all "face zones" but don´t select any thing in "options" and then click "display" you will see the boundary face which you have typed. 2. I think tgrid is same for both 32 and 64 versions.

March 7, 2011, 11:53		#4
me3840 Senior Member Join Date: Nov 2010 Location: USA Posts: 1,232 Rep Power: 24	Thanks for the help on the view portion. I don't think tgrid is the same though - I've run into an "out of memory" error with large meshes. I have 12GB of RAM, so..

May 13, 2011, 07:37		#5
udayrg Member Join Date: Mar 2009 Posts: 32 Rep Power: 17	One more way to locate the region would be put in the desired face node or zone name in the display panel range set a small range and you would see it in the range you have set. i.e. local view........... The 32 bit and 64 bit would be much more same as far as the source code is concerned The Malloc error might occur as your hardware is insufficient to handle the mesh count that's being generated.