[ICEM] How to make a *.msh file using ICEM.

salehi144 · October 24, 2011, 06:42

Hello everyone.

I almost don't know anything about ICEM. But unfortunately i have a *.tin, *.blk and *.prj file. I should make a *.msh file out of those for using it in fluent.

Is there any body that can help me please? it's so important for me.

Regards.

arjun3020 · October 24, 2011, 10:37

you can do it in two ways. 1. from project tree at left side, right click on pre-mesh and then press convert to unstructured. u will get unstructured mesh. then 'go to output tab from main menu. it will show you 4 tab in it, press first tab and select fluent v 6 and ansys. then press second tab and press accept. then directly go to fourth tab and select path to save .msh file.'
2. second way is press file from main menu, in that go to mesh and press load from blocking. u will get unstructured mesh. then do the same as shown by inverted commas.
enjoy.

salehi144 · November 5, 2011, 06:05

Dear arjun.

Tnx alot. that helped. that help so much!

salehi144 · November 5, 2011, 06:06

Dear arjun.

Tnx alot. that helped. that helped so much!

October 24, 2011, 06:42	*How to make a .msh file using ICEM.**	#1
salehi144 New Member Saeed Salehi Join Date: Aug 2010 Posts: 27 Rep Power: 15	Hello everyone. I almost don't know anything about ICEM. But unfortunately i have a .tin, .blk and .prj file. I should make a .msh file out of those for using it in fluent. Is there any body that can help me please? it's so important for me. Regards.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
wmake compiling new solver	mksca	OpenFOAM Programming & Development	14	June 22, 2018 06:29
Problem installing on Ubuntu 9.10 -> 'Cannot open : No such file or directory'	mfiandor	OpenFOAM Installation	2	January 25, 2010 09:50
[Gmsh] Compiling gmshFoam with OpenFOAM-1.5	BlGene	OpenFOAM Meshing & Mesh Conversion	10	August 6, 2009 04:26
[OpenFOAM] ParaView 33 canbt open OpenFoam file	hariya03	ParaView	7	September 25, 2008 17:33
OpenFOAM with IBM AIX	matthias	OpenFOAM Installation	20	March 25, 2008 02:36

October 24, 2011, 10:37		#2
arjun3020 Member arjun Join Date: Oct 2011 Location: Tokyo, JAPAN Posts: 66 Rep Power: 14	you can do it in two ways. 1. from project tree at left side, right click on pre-mesh and then press convert to unstructured. u will get unstructured mesh. then 'go to output tab from main menu. it will show you 4 tab in it, press first tab and select fluent v 6 and ansys. then press second tab and press accept. then directly go to fourth tab and select path to save .msh file.' 2. second way is press file from main menu, in that go to mesh and press load from blocking. u will get unstructured mesh. then do the same as shown by inverted commas. enjoy.

November 5, 2011, 06:05		#3
salehi144 New Member Saeed Salehi Join Date: Aug 2010 Posts: 27 Rep Power: 15	Dear arjun. Tnx alot. that helped. that help so much!

November 5, 2011, 06:06		#4
salehi144 New Member Saeed Salehi Join Date: Aug 2010 Posts: 27 Rep Power: 15	Dear arjun. Tnx alot. that helped. that helped so much!