[ICEM] Generating a Uniform mesh with ICEM

saisanthoshm88 · October 27, 2011, 05:20

To generate a uniform mesh for the Fluid volume in ANSYS workbench I was resorting to body sizing and global mesh settings but in the case of ICEM CFD I don't see any thing like body sizing so would it be just fine to simply go with the global settings over there to get a uniform mesh in ICEM CFD.

BrolY · October 27, 2011, 05:31

Do you want Hexa or Tetra mesh?
For Tetra mesh, you have to create a body (Geometry -> Create Body).
For Hexa mesh, ICEM creates a new part (by default SOLID).

Then, go to Mesh -> Part Mesh Setup and set the size for each part.

saisanthoshm88 · October 27, 2011, 07:10

Thanks for the reply Boles , I meant about the Tetra mesh

PSYMN · October 27, 2011, 08:13

I think Santhosh is talking about setting sizes on a part... More specifically, mesh density within the volume of a part. He probably wants to set this size smaller then is overall global max size.

Under the Mesh tab, you can set sizes by part, but that applies to the surface and curve entities of that part.

ICEM CFD doesn't really have the same concept as a "solid", so if you want to set the max size for a body (the full volume within a part), you really need to create a density region. You can create this around the part, but it will start as a box from min xyz to max XYZ. You can modify the corners to fit better, but some shapes work best with a number of smaller density regions overlapped.

Get started on that and I can answer more specific operational questions later.

saisanthoshm88 · October 27, 2011, 10:07

Many thanks for the reply Simon and yes I was looking for the volumetric size so ill start with the creation of density regions

October 27, 2011, 05:20	Generating a Uniform mesh with ICEM	#1
saisanthoshm88 Senior Member --------- Join Date: Oct 2010 Posts: 303 Rep Power: 17	To generate a uniform mesh for the Fluid volume in ANSYS workbench I was resorting to body sizing and global mesh settings but in the case of ICEM CFD I don't see any thing like body sizing so would it be just fine to simply go with the global settings over there to get a uniform mesh in ICEM CFD. __________________ Best regards, Santhosh.

October 27, 2011, 07:10		#3
saisanthoshm88 Senior Member --------- Join Date: Oct 2010 Posts: 303 Rep Power: 17	Thanks for the reply Boles , I meant about the Tetra mesh __________________ Best regards, Santhosh.

October 27, 2011, 08:13	Mesh Density	#4
PSYMN Senior Member Simon Pereira Join Date: Mar 2009 Location: Ann Arbor, MI Posts: 2,663 Blog Entries: 1 Rep Power: 47	I think Santhosh is talking about setting sizes on a part... More specifically, mesh density within the volume of a part. He probably wants to set this size smaller then is overall global max size. Under the Mesh tab, you can set sizes by part, but that applies to the surface and curve entities of that part. ICEM CFD doesn't really have the same concept as a "solid", so if you want to set the max size for a body (the full volume within a part), you really need to create a density region. You can create this around the part, but it will start as a box from min xyz to max XYZ. You can modify the corners to fit better, but some shapes work best with a number of smaller density regions overlapped. Get started on that and I can answer more specific operational questions later. __________________ ----------------------------------------- Please help guide development at ANSYS by filling in these surveys Public ANSYS ICEM CFD Users Survey This second one is more general (Gambit, TGrid and ANSYS Meshing users welcome)... CFD Online Users Survey

October 27, 2011, 10:07		#5
saisanthoshm88 Senior Member --------- Join Date: Oct 2010 Posts: 303 Rep Power: 17	Many thanks for the reply Simon and yes I was looking for the volumetric size so ill start with the creation of density regions __________________ Best regards, Santhosh.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Free jet simulation	msarkar	OpenFOAM Running, Solving & CFD	39	May 11, 2021 13:21
Pressure instability with rhoSimpleFoam	daniel_mills	OpenFOAM Running, Solving & CFD	44	February 17, 2011 17:08
turbulent jet simulation	antonio_ing	OpenFOAM Running, Solving & CFD	5	September 16, 2010 02:31
problem when converting mesh (made by ICEM) using fluentMeshToFoam	Forrest_Lei	OpenFOAM	11	October 16, 2009 06:28
Convergence moving mesh	lr103476	OpenFOAM Running, Solving & CFD	30	November 19, 2007 14:09

October 27, 2011, 05:31		#2
BrolY Senior Member AB Join Date: Sep 2009 Location: France Posts: 323 Rep Power: 21	Do you want Hexa or Tetra mesh? For Tetra mesh, you have to create a body (Geometry -> Create Body). For Hexa mesh, ICEM creates a new part (by default SOLID). Then, go to Mesh -> Part Mesh Setup and set the size for each part.