[ANSYS Meshing] Extruding 2D mesh to 3D mesh in ANSYS meshing

Rachit · February 6, 2012, 09:01

Hi everyone,

I have been working on a 2D flow over an airfoil in fluent. I had generated the mesh in ANSYS meshing tool. It was an unstructured quad dominant mesh. Now, I have been told to extend the problem in 3D by extruding the same surface mesh in the z direction to convert it into an volume mesh. How could this be accomplished? I know a surface mesh can be extruded in ICEM CFD, but I have been told to do it for the same mesh, so it has to be done in ANSYS meshing only.

Thanks in advance!

Regards,
Rachit

amanbearpig · March 27, 2012, 02:40

Has anyone come up with a solution to this issue? I am having the exact same problem. I can figure out how to extrude a 2D mesh in ICEM to 3D quite well, but how can I do this in Ansys Meshing? Thanks!

mvoss · March 30, 2012, 08:55

i´ve managed to do so by creating a swept mesh,and set the source and target face manually. this means you have to redo ALL your meshing steps at the source face ... so maybe this isn´t what you were looking for.

neewbie

sarangdalne · March 30, 2012, 22:58

Hello,
I guess you have created a sheet/surface model for your analysis. When in the meshing application expand the geometry tree node.. go to the body of interest, now in the details view of that body there must be a field of thickness. give whatever you want.
Thanks,
Sarang

Jordi · July 31, 2012, 06:03

Apparently, a surface can be meshed, a thickness specified and a 2D analysis performed. I'm only missing the possibilty of setting inflations...

Jordi · July 31, 2012, 06:32

But I found it's possible to right-click on the meshing method, the select 'inflate this method' to select edges.

esha · February 14, 2024, 06:22

can you please elaborate the steps?

Gert-Jan · February 14, 2024, 07:49

Have you seen the dates?

esha · February 14, 2024, 07:57

Quote:

Originally Posted by Gert-Jan

Have you seen the dates?

yes, any link with dates and new learners to ask. If you can elaborate then ok otherwise keep quiet please.

Gert-Jan · February 14, 2024, 08:04

It is a matter of managing expectations.
Better start a new query with a well written up-to-date question than to expect people are still there after 12 years. Also, the software has changed significantly since then, so possibly they have a solution that doesn't work for you.

esha · February 14, 2024, 08:19

Quote:

Originally Posted by Gert-Jan

It is a matter of managing expectations.
Better start a new query with a well written up-to-date question than to expect people are still there after 12 years. Also, the software has changed significantly since then, so possibly they have a solution that doesn't work for you.

okay, thank you

February 6, 2012, 09:01	Extruding 2D mesh to 3D mesh in ANSYS meshing	#1
Rachit New Member Rachit Prasad Join Date: Jun 2011 Location: Blacksburg, Virginia Posts: 29 Rep Power: 14	Hi everyone, I have been working on a 2D flow over an airfoil in fluent. I had generated the mesh in ANSYS meshing tool. It was an unstructured quad dominant mesh. Now, I have been told to extend the problem in 3D by extruding the same surface mesh in the z direction to convert it into an volume mesh. How could this be accomplished? I know a surface mesh can be extruded in ICEM CFD, but I have been told to do it for the same mesh, so it has to be done in ANSYS meshing only. Thanks in advance! Regards, Rachit

March 30, 2012, 22:58		#4
sarangdalne New Member Sarang Dalne Join Date: Oct 2010 Posts: 28 Rep Power: 15	Hello, I guess you have created a sheet/surface model for your analysis. When in the meshing application expand the geometry tree node.. go to the body of interest, now in the details view of that body there must be a field of thickness. give whatever you want. Thanks, Sarang dhruvism likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2d meshing in ansys meshing	syler3321	ANSYS Meshing & Geometry	10	November 1, 2012 20:42
How To save a created mesh file in Ansys Meshing	ashtonJ	CFX	4	January 7, 2012 22:04
ANSYS meshing help	s.garg	ANSYS	1	November 12, 2010 04:11
[Other] Ansys meshing - periodic mesh for fluent	jsm	ANSYS Meshing & Geometry	4	September 24, 2010 14:25
Problem importing ANSYS mesh, please help	Ankan Kumar	FLUENT	1	February 2, 2003 08:38

March 27, 2012, 02:40		#2
amanbearpig Member Join Date: Apr 2011 Posts: 57 Rep Power: 14	Has anyone come up with a solution to this issue? I am having the exact same problem. I can figure out how to extrude a 2D mesh in ICEM to 3D quite well, but how can I do this in Ansys Meshing? Thanks!

March 30, 2012, 08:55		#3
mvoss Senior Member Matthias Voß Join Date: Mar 2009 Location: Berlin, Germany Posts: 449 Rep Power: 20	i´ve managed to do so by creating a swept mesh,and set the source and target face manually. this means you have to redo ALL your meshing steps at the source face ... so maybe this isn´t what you were looking for. neewbie

July 31, 2012, 06:03		#5
Jordi New Member Jordi Join Date: May 2010 Posts: 26 Rep Power: 15	Apparently, a surface can be meshed, a thickness specified and a 2D analysis performed. I'm only missing the possibilty of setting inflations...

July 31, 2012, 06:32		#6
Jordi New Member Jordi Join Date: May 2010 Posts: 26 Rep Power: 15	But I found it's possible to right-click on the meshing method, the select 'inflate this method' to select edges.

February 14, 2024, 06:22		#7
esha Member Join Date: Aug 2018 Posts: 85 Rep Power: 7	can you please elaborate the steps?

February 14, 2024, 07:49		#8
Gert-Jan Senior Member Gert-Jan Join Date: Oct 2012 Location: Europe Posts: 1,827 Rep Power: 27	Have you seen the dates?

February 14, 2024, 08:04		#10
Gert-Jan Senior Member Gert-Jan Join Date: Oct 2012 Location: Europe Posts: 1,827 Rep Power: 27	It is a matter of managing expectations. Better start a new query with a well written up-to-date question than to expect people are still there after 12 years. Also, the software has changed significantly since then, so possibly they have a solution that doesn't work for you.