[ICEM] meshing issues in ICEM CFD

acjoshi · April 4, 2012, 23:44

Hello,
I need some help with meshing in ICEM. I have been using GAMBIT all this while but felt the need to speed up my meshing and hence the move to ICEM.

I am trying to mesh a very simple problem with a porous zone.

So the domain consists 1 fluid zone separated by a porous zone.

I am able to create different material points hence hence Cell zones in Fluent.
Domain size 600x800x800mm
I have a porous zone at X = 200 which is 100 wide

I created 2 fluid material points one on each side of the porous zone and assigned the split blocks to it. Assigned the middle block to the Porous zone.

Defined the porous walls as interfaces.

However when I mesh the geometry my 100 mm wide zone has only one cell. The moment I remove the definition of the interface walls the mesh appears correctly.
Can anyone help me with this?

rikio · April 6, 2012, 08:35

It may be the problem of association. Attaching some figures to show your problem may help to find the root cause.

cdegroot · April 7, 2012, 16:10

I have meshed this exact problem except with different dimensions in ICEM. Sounds like it could be an issue in your "part mesh setup". What do the parameters look like for the porous zone and the associated surfaces?

yasinbm · April 14, 2012, 12:01

Whether you are correct in defining the "create body"?

April 4, 2012, 23:44	meshing issues in ICEM CFD	#1
acjoshi New Member ameya Join Date: Apr 2012 Posts: 1 Rep Power: 0	Hello, I need some help with meshing in ICEM. I have been using GAMBIT all this while but felt the need to speed up my meshing and hence the move to ICEM. I am trying to mesh a very simple problem with a porous zone. So the domain consists 1 fluid zone separated by a porous zone. I am able to create different material points hence hence Cell zones in Fluent. Domain size 600x800x800mm I have a porous zone at X = 200 which is 100 wide I created 2 fluid material points one on each side of the porous zone and assigned the split blocks to it. Assigned the middle block to the Porous zone. Defined the porous walls as interfaces. However when I mesh the geometry my 100 mm wide zone has only one cell. The moment I remove the definition of the interface walls the mesh appears correctly. Can anyone help me with this?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[ICEM] Having several dificulties with 3d airfoil meshing in ICEM CFD	Teja	ANSYS Meshing & Geometry	14	February 23, 2015 13:01
[ICEM] Meshing adjacent wall geometry and simple ICEM questions	everdimension	ANSYS Meshing & Geometry	25	June 20, 2012 04:25
Wind tunnel hexa meshing in ICEM CFD 12.1	matheusguzella	ANSYS Meshing & Geometry	1	March 14, 2011 16:14
ICEM CFD Meshing Problems: Hexa Dominant	Evan	CFX	6	July 3, 2006 12:37
Where do we go from here? CFD in 2001	John C. Chien	Main CFD Forum	36	January 24, 2001 21:10

April 6, 2012, 08:35		#2
rikio Senior Member Rikio Join Date: Mar 2009 Location: SH, China Posts: 182 Blog Entries: 1 Rep Power: 17	It may be the problem of association. Attaching some figures to show your problem may help to find the root cause.

April 7, 2012, 16:10		#3
cdegroot Senior Member Chris DeGroot Join Date: Nov 2011 Location: Canada Posts: 414 Rep Power: 17	I have meshed this exact problem except with different dimensions in ICEM. Sounds like it could be an issue in your "part mesh setup". What do the parameters look like for the porous zone and the associated surfaces?

April 14, 2012, 12:01		#4
yasinbm New Member Yasin Besari Mustofa Join Date: Nov 2011 Location: Indonesia Posts: 8 Rep Power: 14	Whether you are correct in defining the "create body"?