Export data on line

Marabelle · November 25, 2013, 03:22

Hello everybody!
I am simulating the flow and heat transfer in a channel. I want to export data in CFD-Post on a line that cuts through my model orthogonally to the flow in the channel. In Inserted a line with Insert>location>line and then exported Data like Turbulence kinetic energy and velocity on that line.

I already found out, that I can vary the samples exported, if I change the number of samples when creating the line. But what I am confused with is, that it exports data also some mm after my model actually ends, they are extremely small (1e-14) but it should export "null" at this points... Does it have to do with my boundary conditions (no slip wall) or is it a problem because Average values are exported? How can I get around this problem? I already tried augmenting the number of samples. Maybe the option "cut" when creating the line helps? But I didn't find anything in the guide about what this option does...
velocity profiles.JPG
I would be grateful for some ideas or tips where I can find how CFD-Post exactly exports the data.
Thanks,
Mara

Marabelle · November 25, 2013, 03:31

ok, I tried out the cut option, seems like it works, but hte problem now is, that I have different nummer of samples on each line and for evaluating my data I already have written a makro where it needs the same number of samples on each line... Any ideas how I can to solve the problem?velocity profiles1_cut.JPG

November 25, 2013, 03:22	Export data on line	#1
Marabelle New Member Tamara Annabelle Join Date: Jul 2013 Posts: 26 Rep Power: 12	Hello everybody! I am simulating the flow and heat transfer in a channel. I want to export data in CFD-Post on a line that cuts through my model orthogonally to the flow in the channel. In Inserted a line with Insert>location>line and then exported Data like Turbulence kinetic energy and velocity on that line. I already found out, that I can vary the samples exported, if I change the number of samples when creating the line. But what I am confused with is, that it exports data also some mm after my model actually ends, they are extremely small (1e-14) but it should export "null" at this points... Does it have to do with my boundary conditions (no slip wall) or is it a problem because Average values are exported? How can I get around this problem? I already tried augmenting the number of samples. Maybe the option "cut" when creating the line helps? But I didn't find anything in the guide about what this option does... velocity profiles.JPG I would be grateful for some ideas or tips where I can find how CFD-Post exactly exports the data. Thanks, Mara

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Other] mesh airfoil NACA0012	anand_30	OpenFOAM Meshing & Mesh Conversion	13	March 7, 2022 17:22
[blockMesh] non-orthogonal faces and incorrect orientation?	nennbs	OpenFOAM Meshing & Mesh Conversion	7	April 17, 2013 05:42
OpenFOAM on MinGW crosscompiler hosted on Linux	allenzhao	OpenFOAM Installation	127	January 30, 2009 19:08
OpenFOAM15 installables are incomplete problem with paraFoam	tryingof	OpenFOAM Bugs	17	December 7, 2008 04:41
Problem of compilation OF 14Allwmake command not found	erik_d	OpenFOAM Bugs	13	September 13, 2008 21:45

November 25, 2013, 03:31		#2
Marabelle New Member Tamara Annabelle Join Date: Jul 2013 Posts: 26 Rep Power: 12	ok, I tried out the cut option, seems like it works, but hte problem now is, that I have different nummer of samples on each line and for evaluating my data I already have written a makro where it needs the same number of samples on each line... Any ideas how I can to solve the problem?velocity profiles1_cut.JPG