CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums

Entries for July 2014

Register Blogs Members List Search Today's Posts Mark Forums Read

Old

Step-by-step SU2 clean parallel Installation (Part 1/3)

Posted July 27, 2014 at 21:31 by pdp.aero
Updated October 3, 2015 at 02:29 by pdp.aero

Long story short, my system has been infected by a malicious. Couldn't remove it, so decided to format the disk and start over fresh. After, I decided to open a blog and share everything that I did for installing the SU2 suite step by step. What you are going to read is step-by-step instruction for installing the SU2 suite after having a clean OS installation. Therefore, there is no precompiled library, packages or third-party software.

All the instruction provided here is based...
Attached Thumbnails
Click image for larger version

Name:	brokenfanvent.jpg
Views:	145
Size:	91.0 KB
ID:	238  
Member
Posted in Uncategorized
Views 2953 Comments 0 pdp.aero is offline Edit Tags
Old

Step-by-step SU2 clean parallel Installation (Part 3/3)

Posted July 27, 2014 at 21:15 by pdp.aero
Updated October 4, 2015 at 12:28 by pdp.aero (Updating to recent version)

For the past

In this section, we are going to install the SU2 2.0.2, pretty old version comparing to current version 3.2.0, and then SU2 2.0.10, after we will finally install the SU2 3.0.0. Again, download the tar file, put the source in a right place, and unpack it. Before building these versions we will need the stands-alone metis.

Metis 4.0.3

Download the tar file from here, put it in your SU2 2.0.2 trunk, then unpack the tar file and direct there....
Member
Posted in Uncategorized
Views 1924 Comments 0 pdp.aero is offline Edit Tags
Old
Rating: 2 votes, 5.00 average.

Step-by-step SU2 clean parallel Installation (Part 2/3)

Posted July 27, 2014 at 21:12 by pdp.aero
Updated October 3, 2015 at 04:51 by pdp.aero (Updating to recent version 3.2.9)

Step 4: Scipy 0.11.0

First, we need be sure about the f2py, which is a requirement. Enter the below command and make sure you have it. You might find it in /usr/local/bin/f2py.
Code:
whereis f2py
In previous step, we checked that numpy is added to python 2.6.6 site package. Now we can go forward and build scipy. Download the source from here, unpack and follow the below commands in your desired directory.

Code:
sudo python setup.py build
sudo python setup.py
...
Member
Posted in Uncategorized
Views 2095 Comments 3 pdp.aero is offline Edit Tags
Old

Influence of mesh size, orientation and type on numerical schemes

Posted July 27, 2014 at 11:13 by Tobi
Updated July 28, 2014 at 04:46 by Tobi

Dear Community,

I am happy and glad to tell you that I finished to analyze all my cases in the investigation of the "Influence of mesh size, orientation and type on numerical schemes in a convective flow field".

Information

  • Investigate into numerical schemes to convective flow field
  • Influence of schemes on mesh size
  • Influence of schemes on mesh type (structured / unstructured)
  • Influence of schemes on mesh/flow orientation (45degree / 0 degree)
...
Tobi's Avatar
Senior Member
Views 768 Comments 0 Tobi is offline Edit Tags
Old

Flamelet Model For OpenFOAM

Posted July 15, 2014 at 09:38 by Tobi

Dear all,

I am working in the topic of the steady state laminar flamelet model since 2012 and used this model in my master thesis for biomass combustion chambers. Therefor I used the built version from Alberto Cuoci et. al. which was generated for OpenFOAM-1.7.x. For my research I used a newer version of OpenFOAM due to the fact of released snappyHexMesh version. Bruno Santos rebuilt the flamelet model for OpenFOAM-1.7.x, 2.0.x, 2.1.x - see here: Bruno Santos Blog about libOpenSMOKE...
Tobi's Avatar
Senior Member
Views 994 Comments 0 Tobi is offline Edit Tags

All times are GMT -4. The time now is 17:34.