CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > CD-adapco

Boundary Errors

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   February 23, 2005, 01:58
Default Boundary Errors
  #1
Shazlan
Guest
 
Posts: n/a
Hi all. I kept on getting this error message. I checked the boundaries many times to locate where the problems may be - but failed. For your info, I am using inlets, outlet (with fixed flow rate) and (static) pressure boundary conditions. There should not be any outflow on the pressure BC, it is there just to indicate the surface is open/expose to atmospheric/ambient pressure. Can somebody please give me a hint on what should I be looking for?

*** WARNING #001 *** FLUID INFLOW DETECTED AT SOME OUTFLOW BOUNDARIES WHERE MASS FLUXES ARE FORCED TO ZERO.

IF THIS CONDITION PERSISTS, YOUR RESULTS MIGHT BE WRONG

THE OUTFLOW BOUNDARY MIGHT NOT BE WELL SPECIFIED OR THE GRID MIGHT BE TOO COARSE NEAR THE OUTFLOW BOUNDARY

Many thanks.

Shazlan
  Reply With Quote

Old   February 23, 2005, 03:38
Default Re: Boundary Errors
  #2
Shazlan
Guest
 
Posts: n/a
Found out that I have cracks in my model. What is the simplest way for me to fix this? I tried vmer with a tolerance of .01 and doesnt work.

If there may be some other errors which leads to the above warning messages (and hence, diverging solution) which I kept on getting, please let me know.

Help is very much appreciated! Shazlan
  Reply With Quote

Old   February 23, 2005, 06:48
Default Re: Boundary Errors
  #3
Volker
Guest
 
Posts: n/a
Are you using a trimmed mesh? If that is the case, you will most likely have your cracks in regions where you don't have a one-to-one cell connectivity. You have to deal with it by generating couples between those cells. Your problem with the outlet-BC might not be related to the cracks (but you should still solve this problem). A cause for this problem can be a recirculation zone at your BC. Try extruding the mesh at the outlet. Or if you get this error message at the beginning of your calculation, just wait a few iterations and it might just go away.

Good luck,

Volker
  Reply With Quote

Old   February 24, 2005, 19:54
Default Re: Cell Errors
  #4
Shazlan
Guest
 
Posts: n/a
Honestly, I am not sure what type of mesh I am using. The grid/mesh was preproduced in Gridgen. Anyway, I fixed the crakcs by going back to Gridgen and did some neccessary changes. The cracks are now gone but there are a few more other errors appeared when I used the Check Grid >> Check All option. They are aspect ration, internal angles, internal face angles and I believe it is the small surface area. My next question is are those errors critical error? or those errors are setting dependant errors (I use all the default 'checking' option in Star-CD) and hence can be ignored? Please advice.

Thanks and have a nice day!
  Reply With Quote

Old   February 25, 2005, 05:36
Default Re: Cell Errors
  #5
Volker
Guest
 
Posts: n/a
OK, if you used an automatic mesher, you will most likely have a tet-mesh (trimmed meshes are a prostar speciality and can be produced in proam). The errors you are getting relate to your cell quality. They are not necessarily knock-out problems like left-handed or concave cells. Nevertheless, you should check where they are and how many cells have a poor quality. Some of the problems can be ignored (e.g. aspect ratios in fine wall boundary cells). You can still try and work with your mesh or you go back and generate a better mesh. Usually that means a finer and larger mesh, extra work and longer computing times. If your mesh isn't a complete desaster, I would give it a go and see if it converges and gives you realistic results. In the mean-time you can generate the better mesh.... Don't forget to extrude your outlet in Star. You can do that by generating shells on your outlet and then use the command vcextrude. After that, you have to do a vmerge and relocate your outlet boundary.

Good luck,

Volker
  Reply With Quote

Old   March 17, 2005, 00:18
Default Re: Cell Errors
  #6
Suresh
Guest
 
Posts: n/a
Dear Volker, I did not get what do u mean by 'Extrude outlet in star'. why do we need to extrude? Hope u provide me some details on that so it will clarify me better.

One more thing,Is vcextrude available in GUI menus?

Regards, Suresh
  Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
pro-am errors azmir CD-adapco 8 January 24, 2006 04:08
Errors in Gambit for boundary layer mesh Mike Spears FLUENT 0 June 23, 2005 11:34
udf errors tata sairamesh FLUENT 1 March 29, 2005 04:01
Cell check and Boundary check errors AB CD-adapco 4 October 28, 2004 13:04
What's these errors for ? Jie FLUENT 1 September 17, 2001 02:36


All times are GMT -4. The time now is 13:38.