CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > CD-adapco

Combustion Problem

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   March 30, 2005, 10:34
Default Combustion Problem
  #1
Arnab
Guest
 
Posts: n/a
My Problem:

I have a rotor with passages and I have one inlet on either side of rotor and 1 exit. From one side of inlet, I have fuel and air in constant proportion (0.1 percent of fuel and rest air of O2 and N2) coming in and from other inlet from other side; I have hot gas(O2 and N2) at high temperature and velocity coming (800 m/s and 1700K). This inlet is used to set up combustion parameters for the fuel air mixture coming from the other inlet. Mine is a high-speed compressible flow rotor with turbulence and shock waves and expansion waves taking place inside the rotor.

To complete the cycle, I need a simple combustion (turbulent combustion) of my fuel (ethylene-air mixture) by the hot gas coming from the other inlet. So now my question is what type of combustion should I use and what are the required parameters I should specify and what it should be.

1. Scheme definition:

Premixed/unpremixed-diffusion/partially premixed?

Which model- EBU standard/EBU

modwall/combined-user/single PPDF?

2. What reaction system should I use? I have to use only 1 step stoichiometric chemical reaction. What do you mean by mixture fraction value and how much should I use? Also should I use "products" in rate equation?

3. As my fuel will get combusted with the temperature of the hot gas coming from the other side, I think I need not specify anything in ignition menu. Am I correct? If no, then what do we mean by fraction burnt?

4. What should I specify as the mass fractions in additional scalar panels for boundary conditions?

  Reply With Quote

Old   April 1, 2005, 05:57
Default Re: Combustion Problem
  #2
Volker
Guest
 
Posts: n/a
Your problem:

1. Partially premixed (do you really have only 0.1 % Fuel?). Try EBU-Standard first. 2. The reaction system comes from your combustion reaction (fuel + O2 -> products). the mixture fraction is calculated by the code. Use products in rate equation. You will probably have to tune Amix and Bmix to get reasonable results. 3. You have to set an ignition if you use EBU. Fraction burnt is the mass fraction of your fuel that is assumed to be burnt already. It is necessary to assume this to get the EBU Model kick-started. You will probably have to tune this value as well. 4. Those are your boundary conditions. You should know the mass fractions of your scalars (fuel ,O2, N2, CO2, etc) at the inlets. 5. I strongly recommend you read the manuals. Be prepared to fail a number of times before you get it right.

Good luck,

Volker
  Reply With Quote

Old   April 29, 2009, 08:13
Default
  #3
New Member
 
mosheu
Join Date: Apr 2009
Posts: 14
Rep Power: 8
hkoten is on a distinguished road
can I use ebu models for diesel combustion
should I close cfm-ecfm button on esice

hkoten@hotmail.com
hkoten is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Combustion problem rupal CFX 0 April 21, 2008 05:29
Combustion problem? Ivar CD-adapco 0 November 7, 2003 08:45
Combustion Problem chetan shah FLUENT 1 October 17, 2003 12:20
combustion problem nabeel mohsin FLUENT 0 September 4, 2003 02:39
Problem with Combustion Jens CFX 6 October 2, 2002 14:18


All times are GMT -4. The time now is 22:24.