CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > CD-adapco

Problems with repeating results

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   May 24, 2006, 08:43
Default Problems with repeating results
  #1
Lee
Guest
 
Posts: n/a
I am trying to duplicate the postprocessing results of one model as I only simulated quarter of the whole model. I did the same thing according to the suggestions of the adapco online website. However, I found that I sucessfully duplicated the geometry but the duplicated the velocity results were not right: the commands only copy the original results to the newly produced geometry area i.e, the directions of those vectors were the same as the original vectors, however, the duplicated vector directions should be symmetrically reflected and be changed.

What is wrong with my doing? How can I get the results that I want?

The followings are the commands I used to get the results: !Set up the coordinate systems CSYS 1 ! - Find the highest vertex number in the model: ! *GET VOFF MXVE ! ! - Make one additional copy of the symmetrical grid in the ! Y direction of CSYS 1 based on the vertex offset ! CSET,NEWS,FLUID CSET,ADD,SOLID CSET,ADD,BAFFLE CGEN,2,VOFF,CSET,,,VREF,1,2

! ! - Load the cell based velocity vectors ! TRLOAD,*.PSTT, STORE,ITER,500 PSYS,1 GETC,ALL POPT,VECT PLTY,QHID ! ! - Calculate the cell offset. Make sure the cell set is the ! same as the original starting collection. ! *GET,COFF,NCSET ! - Copy the vector data to the duplicate parts DGEN,2,COFF,CSET CSET,ALL CPLOT

Thank you very much for your help!

Lee
  Reply With Quote

Old   May 24, 2006, 10:38
Default Re: Problems with repeating results
  #2
Ralphie
Guest
 
Posts: n/a
I could be wrong but I think this only works when you have compressed your cells before the simulation. Any 'empty' cell numbers in your original model are not transferred to the copied geometry, therefore your post data is copied to the wrong place. Hope that made sense...
  Reply With Quote

Old   May 24, 2006, 13:37
Default Re: Problems with repeating results
  #3
Lee
Guest
 
Posts: n/a
First thank you very much for your help, Ralphie!

However, I have to point out that I did compress my cells by using "ccom and vcom" commands before the simulation and before the time I duplicated the results. As my simulated results have some turbulent flows in the solution domain, so the velocity directions are not the same for different points.

I just wonder that problem should not be come out.

Anyway, I guess maybe STAR-Cd only copy the different velocity components to the newly generated geometries and will not do some correspondent changes, for example, when the whole original geometry is reflected about Y axis, the original positive X component of the velocity will be kept as positive value rather than negative value which should be negative in fact after duplication. The description of the command "dgen" just says this point.

I still want to know how to realize the right duplication, hopefully someone can give me further guide.

Thanks a lot for any help!

Lee

  Reply With Quote

Old   May 25, 2006, 07:02
Default Re: Problems with repeating results
  #4
Anton Lyaskin
Guest
 
Posts: n/a
Try loading your velocity components (before you copy them) in cylinrdical coordinate system (check PSYS command)
  Reply With Quote

Old   May 26, 2006, 03:39
Default Re: Problems with repeating results
  #5
Ralphie
Guest
 
Posts: n/a
I understand your problem now. Use the CHANGE command for the component you want to modify. Put all new cells in a set (after loading and copying of your vector data), then do

CHANGE CSET,,,-1 0 1 1

if you want to change the X component. This will do

-1 * X + 0 for post registers 1 to 1

There is a designated Post-Processing manual in the Star V4 documentation. Chapter 6 explains mirroring symmetric geometries and results. Good Luck!
  Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Simple test problems with known results kar OpenFOAM 0 March 15, 2008 08:54
Convergence/results problems in a model Isaac Phoenics 0 April 18, 2007 03:05
problems viewing results with VNC Ralf Schmidt FLUENT 3 February 1, 2006 02:40
Repeating same time steps (FSI) CJ Tune CD-adapco 0 February 25, 2003 21:27
Repeating the same calculations CFD Man Main CFD Forum 1 August 15, 2002 00:54


All times are GMT -4. The time now is 13:26.