CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > CD-adapco

Inlet air preheating

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   September 14, 2006, 20:51
Default Inlet air preheating
  #1
usker
Guest
 
Posts: n/a
I am trying to simulate a gas burner (transient, unremixed/diffusion combustion). First I calculated temperature and NOx with inlet air temperature 293K. Now I want to calculate with inlet air preheating. I selected 3 different air temperatures 473,673 and 873K. I insert these temp values into "Define Boundary Regions" and I also insert the air density at that particular temperature (for example temp-473K, density-0.738404kg/m3). The solution method and analysis controls are the same for every case. But when I get the results of Temperature and NOx distribution, the values of flame temp and NOx appears to be the same for all conditions (temp 293,473,673 and 873). Could you please advise what I have to do to get correct results.

Regards
  Reply With Quote

Old   September 17, 2006, 11:27
Default Re: Inlet air preheating
  #2
Mike H
Guest
 
Posts: n/a
One possible reason for this is that you may be using the Presumed Probability Density Function model in version 3.26.

This model (in version 3.26) doesn't allow you to change the boundary temperature in the BC panel - you have to change it in the combustion model setup. The BC panel only determines the mass flow rate as the product of your velocity and density if you're using the 'Mass flux' option.

This has been fixed in Star-CCM+ and I think in Star-CD version 4.0 also but I'm not sure.

If you are using the eddy breakup model then something else is wrong with your model.

Good luck - Mike
  Reply With Quote

Old   September 20, 2006, 04:27
Default Re: Inlet air preheating
  #3
usker
Guest
 
Posts: n/a
I have used CEA with PPDF. I have assigned temperature 873K for the air inlet. If I assign higher temperature in CEA for air inlet then I get higher flame temperature. But shouldn't it be like if the temperature increases, at atmosheric pressure, then the air density decreases, which means the mass of air (or mass flow rate) also decreases. This can affect the reaction rate, the reaction rate becomes slower and adiabatic flame temperature decreases, and therefore, NOx also decreases. In Boundary Conditions I have assigned velocity, air density (with respect to temperature). But it seems to me that Pro-Star does not sense anyhow the changes in density and temperature in BC. It only senses the temperature changes in CEA (chemical equilibrium with applications), without considering the change in mass flow rate.

Could anybody advise please, how to calculate this kind of problem with inlet air preahiting and propane combustion.

Regards
  Reply With Quote

Old   September 21, 2006, 08:21
Default Re: Inlet air preheating
  #4
Ralphie
Guest
 
Posts: n/a
Try Switch 127.
  Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
velocity inlet vs pressure inlet cheong FLUENT 6 April 9, 2011 03:07
subsonic inlet or supersonic inlet? mali CFX 0 November 28, 2008 21:57
reversed flow at velocity inlet / mass flow inlet ib FLUENT 1 March 26, 2007 13:11
How to set smoke inlet speed on inlet Adam FLUENT 0 October 4, 2005 08:18
inlet B.cs cfdbig Main CFD Forum 1 August 9, 2004 02:35


All times are GMT -4. The time now is 19:55.