trimmer mesh vs Polyhedral mesh

Marcelo · April 30, 2009, 16:56

Dear All,

I need to mesh a complicate shape, with the trimmer mesher is easier but I dont know if this method have some disadvantage in front Polyhedral StarCCM+ mesh...

vishyaroon · May 1, 2009, 11:31

Both trimmer and polyhedral should work well. I had carried out a comparitive study for heat exchangers and showed no difference.

You mention that your's is a complex case. Can you tell me what case it is? If the geometry is complicated both these schemes can handle it. If you have additional physics like CHT or something, one may be better than the other. for eg. polyhedral is supposed to be better in CHT as you can use the same mesh continua for both solid and fluid.

chris1232 · February 4, 2015, 09:00

Hi,

Im confusing which mesh should be bettwer for aircraft's winglets analysis. I will be changing the length and the cant angle of a winglet and see how its affects the CL, CD etc.

Should I go for Trimmer mesh as it is probably faster and good or should I go for Polyhedral mesh?

It will be part of a wing tested which will be 6m long. Tested uder 20m/s 60m/s and 100m/s at constant AOA

Any idea of what settings should I apply for the mesh?

Thanks.

April 30, 2009, 16:56	trimmer mesh vs Polyhedral mesh	#1
Marcelo New Member Marcelo Join Date: Mar 2009 Location: Valparaiso Chile Posts: 26 Rep Power: 17	Dear All, I need to mesh a complicate shape, with the trimmer mesher is easier but I dont know if this method have some disadvantage in front Polyhedral StarCCM+ mesh...

February 4, 2015, 09:00	Aircraft's winglets analysis	#3
chris1232 New Member Chris Join Date: Jan 2015 Posts: 2 Rep Power: 0	Hi, Im confusing which mesh should be bettwer for aircraft's winglets analysis. I will be changing the length and the cant angle of a winglet and see how its affects the CL, CD etc. Should I go for Trimmer mesh as it is probably faster and good or should I go for Polyhedral mesh? It will be part of a wing tested which will be 6m long. Tested uder 20m/s 60m/s and 100m/s at constant AOA Any idea of what settings should I apply for the mesh? Thanks.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[Technical] Polyhedral mesh generation	lr103476	OpenFOAM Meshing & Mesh Conversion	49	July 17, 2012 02:59
Dynamic moving mesh	Pei-Ying Hsieh (Hsieh)	OpenFOAM Running, Solving & CFD	64	June 7, 2012 10:04
ICEM 10 mesh question	DAK565656	CFX	6	May 8, 2007 12:16
Icemcfd 11: Loss of mesh from surface mesh option?	Joe	CFX	2	March 26, 2007 18:10
Fluent 6.3.16 + Polyehdral Meshes	Carlos	FLUENT	3	March 15, 2007 03:09

May 1, 2009, 11:31		#2
vishyaroon Senior Member Aroon Join Date: Apr 2009 Location: Racine WI Posts: 148 Rep Power: 17	Both trimmer and polyhedral should work well. I had carried out a comparitive study for heat exchangers and showed no difference. You mention that your's is a complex case. Can you tell me what case it is? If the geometry is complicated both these schemes can handle it. If you have additional physics like CHT or something, one may be better than the other. for eg. polyhedral is supposed to be better in CHT as you can use the same mesh continua for both solid and fluid.