Need some assistance in modelling

naresh007 · January 21, 2014, 07:10

Project details below

To study and compare the spray length, cone angle of the spray and droplet size inside the cylinder of petrodiesel and biodiesel.
. 3 orifices at 120° each
. At the end of compression,
Air pressure = 30-40 bar at 250° C
Fuel pressure = 250 bar

Arrangement : A cylinder arrangement of a diesel engine with the two valves in the closed position. An injector is placed in the middle vertically, the nozzle tip has 3 orifices placed at 120° each. Orifice dia being 0.6mm.
All the dimensions of the cylinder arrangement to be taken according to any specific standard.

sarab · January 21, 2014, 10:35

Dear if you need simulations using Ansys CFX. I can help you. you can contact me with details.

Hemen Shah · January 21, 2014, 10:36

Hello Naresh,

Hi-Tech Engineering will be happy to assist you in your project.

Please visit :
Hi-Tech: Engineering Services - CAE, FEA, CFD : http://bit.ly/Hi-Tech-CAE-FEA-CFD-Services

To view our services and case studies.

Our services are cost effective and we will be happy to get associated with your organization.

Looking forward to hear from you.

Regards
Hemen Shah.
www.hitechos.com
hemen.shah@hitechos.com.

January 21, 2014, 07:10	Need some assistance in modelling	#1
naresh007 New Member Join Date: Jan 2014 Posts: 9 Rep Power: 12	Project details below To study and compare the spray length, cone angle of the spray and droplet size inside the cylinder of petrodiesel and biodiesel. . 3 orifices at 120° each . At the end of compression, Air pressure = 30-40 bar at 250° C Fuel pressure = 250 bar Arrangement : A cylinder arrangement of a diesel engine with the two valves in the closed position. An injector is placed in the middle vertically, the nozzle tip has 3 orifices placed at 120° each. Orifice dia being 0.6mm. All the dimensions of the cylinder arrangement to be taken according to any specific standard.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Assistance for modelling unsteady supersonic flow in FLUENT	SATISH A.V	FLUENT	11	October 1, 2014 22:36
kOmegaSST without turbulence modelling of the flow around geometry	CFDnewbie147	OpenFOAM Running, Solving & CFD	7	December 5, 2013 07:29
error message	cuteapathy	CFX	14	March 20, 2012 06:45
Advice on multi-phase flow modelling	Martin	Main CFD Forum	3	October 14, 2008 05:16
Unsteady modelling technique?	Carlos	FLUENT	0	September 26, 2008 11:37

January 21, 2014, 10:35		#2
sarab New Member Join Date: Jan 2014 Posts: 2 Rep Power: 0	Dear if you need simulations using Ansys CFX. I can help you. you can contact me with details.

January 21, 2014, 10:36		#3
Hemen Shah New Member Hemen Shah Join Date: Jul 2013 Posts: 29 Rep Power: 12	Hello Naresh, Hi-Tech Engineering will be happy to assist you in your project. Please visit : Hi-Tech: Engineering Services - CAE, FEA, CFD : http://bit.ly/Hi-Tech-CAE-FEA-CFD-Services To view our services and case studies. Our services are cost effective and we will be happy to get associated with your organization. Looking forward to hear from you. Regards Hemen Shah. www.hitechos.com hemen.shah@hitechos.com.