ANSYS 13 Multifield,

mechanicaldesign · May 20, 2012, 00:42

Hi to all,

I have a question referring to study fluid flow and thermal using CFX from ANSYS 13.

How I observe, in last period ANSYS put very much accent on Workbench module. I am using ANSYS MAPDL. So, my question is : the version of ANSYS 13 can made coupled simulation (two ways simulation or MFX) using CFX and ANSYS MAPDL, or only using Workbench module?

because this type of coupled study in the past (old version of ANSYS) it was possible.

Thank you in advance for advice and answer.

Best regards.

ghorrocks · May 20, 2012, 07:29

Yes, it is possible. Workbench justs generates the APDL for the simualtion, so I guess if you used the same APDL you can do it without workbench. I would run a test MFX simulation and have a look at the APDL and command lines it uses to do it.

p.galimutti · May 26, 2012, 09:32

Yes, you don't need work bench for multi-filed simulation. It's just an interface bringing all Ansys programs under one roof!

ps: I believe if you want to do multifield simulation with CFX as the flow solver, you may not be able to do it MAPDL itself. You just create a data file in MAPDL with b.c's & coupling conditions etc, which will be read into CFX. CFX does the rest of the interactive analysis.

If you want to do entire analysis in MAPDL, Flotran does the flow solving.

May 20, 2012, 00:42	ANSYS 13 Multifield,	#1
mechanicaldesign Member adminCAE Join Date: Aug 2009 Location: Timisoara Posts: 63 Rep Power: 16	Hi to all, I have a question referring to study fluid flow and thermal using CFX from ANSYS 13. How I observe, in last period ANSYS put very much accent on Workbench module. I am using ANSYS MAPDL. So, my question is : the version of ANSYS 13 can made coupled simulation (two ways simulation or MFX) using CFX and ANSYS MAPDL, or only using Workbench module? because this type of coupled study in the past (old version of ANSYS) it was possible. Thank you in advance for advice and answer. Best regards. __________________ Mess with the best die like the rest ... ANSYS is the best !!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Command Line Run for ANSYS	Liaquat	ANSYS	11	April 19, 2018 09:49
Fluid structure interaction	jnattia	Main CFD Forum	25	May 21, 2015 09:16
Ansys workbench problem	Jonny6001	ANSYS	2	September 30, 2010 12:59
FSI Simulation unsing ANSYS Multifield	k_buz	CFX	2	April 6, 2009 17:40
Exporting results from CFX to ANSYS ??	sohail ahmed	CFX	1	December 20, 2007 01:10

May 20, 2012, 07:29		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Yes, it is possible. Workbench justs generates the APDL for the simualtion, so I guess if you used the same APDL you can do it without workbench. I would run a test MFX simulation and have a look at the APDL and command lines it uses to do it.

May 26, 2012, 09:32		#3
p.galimutti Member Peter Galimutti Join Date: May 2012 Posts: 37 Rep Power: 13	Yes, you don't need work bench for multi-filed simulation. It's just an interface bringing all Ansys programs under one roof! ps: I believe if you want to do multifield simulation with CFX as the flow solver, you may not be able to do it MAPDL itself. You just create a data file in MAPDL with b.c's & coupling conditions etc, which will be read into CFX. CFX does the rest of the interactive analysis. If you want to do entire analysis in MAPDL, Flotran does the flow solving.