Time average Result in transient Run

omidiut · July 27, 2013, 02:02

Hi all

I simulate flow post a cylinder, transient simulation done. As you know in CFD-Post you can get contour, streamline ,... for any time using time selector. My question is:

How can i get time averaged result in a transient simulation? like stream lines, contours, etc.

Best regards.

ghorrocks · July 27, 2013, 07:15

The best way of doing this is to calculate these variable fields during simulation time. Then the variables are present in post processing.

omidiut · July 27, 2013, 07:28

Quote:

Originally Posted by ghorrocks

The best way of doing this is to calculate these variable fields during simulation time. Then the variables are present in post processing.

Thank you for your reply Dear ghorrocks
I need to calculate time average of variables like Pressure, velocity, at each point of mesh, not at whole domain. How can i do that?

Best regards.

ghorrocks · July 27, 2013, 07:36

As I said, have a look at the transient averaging variables in the documentation.

omidiut · July 27, 2013, 07:49

Quote:

Originally Posted by ghorrocks

As I said, have a look at the transient averaging variables in the documentation.

Would you mind help more?

ghorrocks · July 27, 2013, 07:50

Set up transient time averaging of some variables in the output tab in Pre.

omidiut · July 27, 2013, 08:05

Quote:

Originally Posted by ghorrocks

Set up transient time averaging of some variables in the output tab in Pre.

Thank you very much.
Do you mean "Trn Stats" ?

ghorrocks · July 28, 2013, 07:35

Yes, that's right.

July 27, 2013, 02:02	Time average Result in transient Run	#1
omidiut Senior Member omid Join Date: Apr 2011 Posts: 105 Rep Power: 14	Hi all I simulate flow post a cylinder, transient simulation done. As you know in CFD-Post you can get contour, streamline ,... for any time using time selector. My question is: How can i get time averaged result in a transient simulation? like stream lines, contours, etc. Best regards.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
y+ and u+ values with low-Re RANS turbulence models: utility + testcase	florian_krause	OpenFOAM	114	August 23, 2023 05:37
Floating point exception error	Alan	OpenFOAM Running, Solving & CFD	11	July 1, 2021 21:51
AMI interDyMFoam for mixer nu problem	danny123	OpenFOAM Programming & Development	8	September 6, 2013 02:34
mixerVesselAMI2D's mass is not balancing	sharonyue	OpenFOAM Running, Solving & CFD	6	June 10, 2013 09:34
calculation stops after few time steps	sivakumar	OpenFOAM Running, Solving & CFD	7	March 17, 2013 06:37

July 27, 2013, 07:15		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,692 Rep Power: 143	The best way of doing this is to calculate these variable fields during simulation time. Then the variables are present in post processing.

July 27, 2013, 07:36		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,692 Rep Power: 143	As I said, have a look at the transient averaging variables in the documentation.

July 27, 2013, 07:50		#6
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,692 Rep Power: 143	Set up transient time averaging of some variables in the output tab in Pre.

July 28, 2013, 07:35		#8
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,692 Rep Power: 143	Yes, that's right.