Error

amin.z · October 4, 2013, 09:55

hi
what's the meaning of this error:
"The CFX solver for system 'modelname' did not produce a results file"

when I run the solution, I see this error:
"The ANSYS CFX solver could not be started, or exited with return code 255:
No results file has been created."

saeed115 · October 7, 2013, 13:19

maybe you have illegal copy of that software....check your software is active or not.you have to have an activate key...................G.luck

ghorrocks · October 7, 2013, 17:44

This error does not imply it is pirated software. It simply means a simulation did not complete so not results file was generated. You would need to look into the details of the simulation setup to find what the error is.

rameezib · October 8, 2013, 01:53

When this message pops out, close it, and have a closer view on the right hand section of the solver run, there you will get the exact error. Error might be due to some in appropriate boundary setting or due to output control setting. Thanks

amin.z · October 8, 2013, 16:28

Dear freinds!
thanks from you!
but my software license is valid and it works correctly
I checked the simulation again but it hasn't any result!

ghorrocks · October 8, 2013, 18:02

As I said, this error has nothing to do with licensing. You have a problem with your simulation setup. You would have to post more details about what you are doing if we are to help you.

amin.z · October 9, 2013, 08:50

I'm modeling a simple 2D nozzle in CFX

geometry
http://www.cfd-online.com/Forums/att...1&d=1381322772

mesh
http://www.cfd-online.com/Forums/att...1&d=1381322794

setup
http://www.cfd-online.com/Forums/att...1&d=1381322811

ghorrocks · October 9, 2013, 17:39

We still have no idea what you are modelling - see: http://www.cfd-online.com/Wiki/Ansys...ible_answer.3F

amin.z · October 13, 2013, 02:25

Dear ghorrocks!
as you said the error was due to incorrect settings in the simulation setup.
I checked it and solve this error

thanks for your help
good luck!

saeed115 · October 25, 2013, 08:49

he simulate a symmetry airfoil...i think

October 4, 2013, 09:55	Error	#1
amin.z Senior Member Amin Join Date: Oct 2013 Location: Germany Posts: 397 Rep Power: 14	hi what's the meaning of this error: "The CFX solver for system 'modelname' did not produce a results file" when I run the solution, I see this error: "The ANSYS CFX solver could not be started, or exited with return code 255: No results file has been created."

October 7, 2013, 13:19	hi Dear	#2
saeed115 New Member saeed Join Date: Feb 2013 Posts: 19 Rep Power: 13	maybe you have illegal copy of that software....check your software is active or not.you have to have an activate key...................G.luck

October 7, 2013, 17:44		#3
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	This error does not imply it is pirated software. It simply means a simulation did not complete so not results file was generated. You would need to look into the details of the simulation setup to find what the error is. amin.z likes this.

October 8, 2013, 01:53		#4
rameezib New Member Rameez Join Date: May 2013 Posts: 19 Rep Power: 12	When this message pops out, close it, and have a closer view on the right hand section of the solver run, there you will get the exact error. Error might be due to some in appropriate boundary setting or due to output control setting. Thanks amin.z likes this.

October 8, 2013, 16:28	Thanks	#5
amin.z Senior Member Amin Join Date: Oct 2013 Location: Germany Posts: 397 Rep Power: 14	Dear freinds! thanks from you! but my software license is valid and it works correctly I checked the simulation again but it hasn't any result!

October 8, 2013, 18:02		#6
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	As I said, this error has nothing to do with licensing. You have a problem with your simulation setup. You would have to post more details about what you are doing if we are to help you. amin.z likes this.

October 9, 2013, 17:39		#8
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	We still have no idea what you are modelling - see: http://www.cfd-online.com/Wiki/Ansys...ible_answer.3F

October 13, 2013, 02:25		#9
amin.z Senior Member Amin Join Date: Oct 2013 Location: Germany Posts: 397 Rep Power: 14	Dear ghorrocks! as you said the error was due to incorrect settings in the simulation setup. I checked it and solve this error thanks for your help good luck!

October 25, 2013, 08:49	good luck amin	#10
saeed115 New Member saeed Join Date: Feb 2013 Posts: 19 Rep Power: 13	he simulate a symmetry airfoil...i think

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
[swak4Foam] GroovyBC the dynamic cousin of funkySetFields that lives on the suburb of the mesh	gschaider	OpenFOAM Community Contributions	300	October 29, 2014 18:00
c++ libraries and solver compiling	vaina74	OpenFOAM Installation	13	February 3, 2012 17:43
[OpenFOAM] Saving ParaFoam views and case	sail	ParaView	9	November 25, 2011 15:46
DecomposePar links against liblamso0 with OpenMPI	jens_klostermann	OpenFOAM Bugs	11	June 28, 2007 17:51
user defined function	cfduser	CFX	0	April 29, 2006 10:58