CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

Particle Diagnostics

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   August 8, 2015, 13:00
Default Particle Diagnostics
  #1
New Member
 
Join Date: Jul 2015
Posts: 3
Rep Power: 10
Hicha04m is on a distinguished road
Hi,

i simulate fluid with particle and use User routine to calculate the drag coefficient but i get 0


Particle Diagnostics
================================================== ====================

+--------------------------------------------------------------------+
| Particle Fate Diagnostics |
+--------------------------------------------------------------------+
| Particle type | Fate type Particles |
+--------------------------------------------------------------------+
| Particle | Entered domain : 1000 |
| | Left domain : 1000 |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| Particle Equation | Total source and source change rates |
+--------------------------------------------------------------------+
| | Equation Source Rate |
+--------------------------------------------------------------------+
| Domain: Default Domain |
+--------------------------------------------------------------------+
| Particle | x-Mom 0.000E+00 0.0000 |
| | y-Mom 0.000E+00 0.0000 |
| | z-Mom 0.000E+00 0.0000 |
+--------------------------------------------------------------------+
Hicha04m is offline   Reply With Quote

Old   August 8, 2015, 22:35
Default
  #2
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,665
Rep Power: 143
ghorrocks is just really niceghorrocks is just really niceghorrocks is just really niceghorrocks is just really nice
Have a think about what the message is saying. It is saying it generated 1000 particles and 1000 particles left the domain. The source term bit states none of these particles interacted with the flow.

So I suspect some combination of:
* You seeded the particles outside the domain
* You seeded the particles on a boundary which was flowing out
* Your particle time step was so large that they wizzed right across the domain in one time steps.
* Or something else where the particles do not interact with the domain.
ghorrocks is offline   Reply With Quote

Old   August 9, 2015, 06:23
Default
  #3
New Member
 
Join Date: Jul 2015
Posts: 3
Rep Power: 10
Hicha04m is on a distinguished road
Thank you for your answer. I get now this message


Parallel run: Received message from slave
-----------------------------------------
Slave partition : 3
Slave routine : ErrAction
Master location : RCVBUF,MSGTAG=1032
Message label : 001100279
Message follows below - :

+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| c_fpx_handler: Floating point exception: Overflow |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+

Parallel run: Received message from slave
-----------------------------------------
Slave partition : 3
Slave routine : ErrAction
Master location : RCVBUF,MSGTAG=1032
Message label : 001100279
Message follows below - :

+--------------------------------------------------------------------+
| ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Stopped in routine FPX: c_fpx_handler |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+

+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX solver exited with return code 1. No results file |
| has been created. |
+--------------------------------------------------------------------+

End of solution stage.
Hicha04m is offline   Reply With Quote

Old   August 9, 2015, 21:02
Default
  #4
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,665
Rep Power: 143
ghorrocks is just really niceghorrocks is just really niceghorrocks is just really niceghorrocks is just really nice
FAQ: http://www.cfd-online.com/Wiki/Ansys...do_about_it.3F
ghorrocks is offline   Reply With Quote

Old   August 12, 2015, 03:29
Default
  #5
Senior Member
 
Join Date: May 2012
Location: Melbourne
Posts: 161
Rep Power: 13
Steffen595 is on a distinguished road
in other words, you get 0 because it did not run the calc in the 1st place
Steffen595 is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
UDF for particle interception with pt_termination fortran routine abcdefgh CFX 6 October 6, 2019 14:30
injection problem Mark New FLUENT 0 August 4, 2013 02:30
Particle tracking prob, urgent. sakurabogoda CFX 1 March 11, 2013 22:11
Particle Transport Modelling - Fate Diagnostics leeportnoff CFX 9 January 12, 2012 10:48
DPM UDF particle position using the macro P_POS(p)[i] dm2747 FLUENT 0 April 17, 2009 02:29


All times are GMT -4. The time now is 20:49.