CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

Solver Software (?) problems

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   July 31, 2002, 17:46
Default Solver Software (?) problems
  #1
JvK
Guest
 
Posts: n/a
Hi,

I'm running distributed parallel jobs on a Linux-cluster (2 dual proc nodes and 1 master). Sometimes my job exits suddenly with the following message: The CFX-5 Solver exited with return code 1. No results file has been created.

What is return code 1? It's very annoying, because sometimes this happens after a lot of calculation hours, and because there is no results file, I cannot restart the job.

Regards, Jaap
  Reply With Quote

Old   August 1, 2002, 20:54
Default Re: Solver Software (?) problems
  #2
Hannah liang
Guest
 
Posts: n/a
Me too. I met this problem so many times. I think it's the software's problem.

Hannah
  Reply With Quote

Old   August 2, 2002, 04:42
Default Re: Solver Software (?) problems
  #3
sharks
Guest
 
Posts: n/a
Hi Jaap

As a matter of course, I always run the CFX-5 Solver with Backup Results switched on (usually every 20 to 50 iterations), which can be used to restart the Solver should the run fail.

Regards,

Sharks
  Reply With Quote

Old   August 5, 2002, 18:29
Default Re: Solver Software (?) problems
  #4
JvK
Guest
 
Posts: n/a
Of course you should turn on the backup option. However, when using this option, you lose all your RMS residual data of the previous steps AND I cannot determine at which nodes my maximal RMS residuals have taken place. Do you have a solution for this problem?

Regards,

Jaap
  Reply With Quote

Old   August 5, 2002, 18:30
Default Re: Solver Software (?) problems
  #5
JvK
Guest
 
Posts: n/a
Thank you for your response. On which platform are you running CFX 5?

Regards Jaap
  Reply With Quote

Old   August 9, 2002, 14:33
Default Re: Solver Software (?) problems
  #6
Neale
Guest
 
Posts: n/a
Just set turn on equation residuals output in CFX-Build. You could look at them in CFX-Post.

As for your original problem, is there any message in the output file in addition to the return code 1 exit message. Maybe the solver is crashing, or something, did you take the time to look at the output file and figure it out? It might not be the software either, sometimes a poorly setup and maintained Linux cluster (eg: you just slapped together a bunch of cheap PCs) will create problems. Maybe you need some new network cards, or new motherboards or something?

Neale.
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Creating New Solver: For particle-laden compressible jets sankarv OpenFOAM Running, Solving & CFD 17 December 3, 2014 20:41
Problems about buoyantBoussinesqSimpleFoam solver chiven OpenFOAM Running, Solving & CFD 9 October 27, 2014 15:39
Quarter Burner mesh with periosic condition SamCanuck FLUENT 2 August 31, 2011 12:34
multiphase solver for steady state problems lionlove0903 OpenFOAM 0 January 5, 2011 08:41
Setting a B.C using UserFortran in 4.3 tokai CFX 10 July 17, 2001 17:25


All times are GMT -4. The time now is 14:37.