CFX4 Build

November 24, 2003, 23:24

Can somebody in this forum give me a hand/help on how to generate structured grid in CFX4 Build for a circular pipe?

November 25, 2003, 03:59

You need to create a H block, meaning that you have a central square that is connected to the outer (4) circle of the pipe. It is well described in the manual.

November 25, 2003, 04:01

November 25, 2003, 04:01

You need to create a H block, meaning that you have a central square that is connected to the outer (4) circle of the pipe. It is well described in the manual.

November 25, 2003, 04:33

November 25, 2003, 06:03

Just before Jan takes a nap, remember that (say) if y becomes your radial direction in the solver, it should not be less than zero.

Eldoret

November 25, 2003, 07:14

For a 3D carthesian calculation why should it be a problem with y less that zero. (Still ZZZZZZZZ) Jan

December 10, 2003, 01:01

It only matters in a 2D axisymmetric grid (Y's should all be positive). In a 3D grid it matters not.

There's a standard example in the docs.

Jeff

November 24, 2003, 23:24	CFX4 Build	#1
KKA Guest Posts: n/a	Can somebody in this forum give me a hand/help on how to generate structured grid in CFX4 Build for a circular pipe?

November 25, 2003, 03:59	Re: CFX4 Build	#2
Jan Rusås Guest Posts: n/a	You need to create a H block, meaning that you have a central square that is connected to the outer (4) circle of the pipe. It is well described in the manual.

November 25, 2003, 04:01	Ups -did not see your post further down	#3
Jan Rusås Guest Posts: n/a

November 25, 2003, 04:01	Re: CFX4 Build	#4
Jan Rusås Guest Posts: n/a	You need to create a H block, meaning that you have a central square that is connected to the outer (4) circle of the pipe. It is well described in the manual.

November 25, 2003, 04:33	Hmm, not sure what is going on - better take a nap	#5
Jan Rusås Guest Posts: n/a

November 25, 2003, 06:03	Re: CFX4 Build	#6
Eldoret Guest Posts: n/a	Just before Jan takes a nap, remember that (say) if y becomes your radial direction in the solver, it should not be less than zero. Eldoret

November 25, 2003, 07:14	Re: CFX4 Build	#7
Jan Rusås Guest Posts: n/a	For a 3D carthesian calculation why should it be a problem with y less that zero. (Still ZZZZZZZZ) Jan

December 10, 2003, 01:01	Re: CFX4 Build	#8
Jeff Guest Posts: n/a	It only matters in a 2D axisymmetric grid (Y's should all be positive). In a 3D grid it matters not. There's a standard example in the docs. Jeff

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
64bitrhel5 OF installation instructions	mirko	OpenFOAM Installation	2	August 12, 2008 18:07
OpenFOAM build from source instructions	tj22	OpenFOAM Installation	7	April 6, 2006 16:15
BUILD MESH: CFX4	RK	CFX	0	June 25, 2005 06:12
Unigraphics -> CFX4 Build	Vincent	CFX	1	February 11, 2003 16:04
CFX Build 5 question...	cfd guy	CFX	6	June 19, 2001 22:38