Does Ansys workbench can import .cdb file as load?

December 18, 2006, 20:58

Hi:

i export some temperature and stress to .cdb files in CFX.

And i want to use the files as load in Ansys workbench,

can i do it successfully?

thanks in advance!!!~~~

December 19, 2006, 23:41

is there anyone help me or give me some advise~~~

thanks a lot~

fredcab66 · April 20, 2010, 03:23

I have the same problem.
I would like to import a .cdb file ( from fluent) in workbench , is it possible?
information : it is a 2d problem , i juste want to import pressure on a edge.

Thanks!

Fred

stumpy · April 20, 2010, 15:39

Something like the following Command Snipet in WB should do it:

/PREP7
/inp,filename,sfe
/SOLVE

fredcab66 · April 20, 2010, 15:48

Thanks Stumpy for your reply .
I will try it !
thanks again!

Fred

fredcab66 · April 24, 2010, 07:24

Helo stumpy ,

I have tryed a lot , but i con't import load .

Could you explain more your solution please?

Whant kind ( and extension) of file can i import?
Where do i generate this file ( cfd post, fluent)?

I tryed the export from fluent in cdb, but i failed , the Snipet was not enough readable.

thanks again!

cheers

fred

Ohbuchi · April 26, 2010, 01:43

If you mentioned about cmdb (Meshing) not cdb (Mechanical APDL), you can import by File->import.
If your cmdb file contains CFX-Mesh data created by release 10, you should import by release 11 first and save as release 11 data.

December 18, 2006, 20:58	Does Ansys workbench can import .cdb file as load?	#1
prayskyer Guest Posts: n/a	Hi: i export some temperature and stress to .cdb files in CFX. And i want to use the files as load in Ansys workbench, can i do it successfully? thanks in advance!!!~~~

December 19, 2006, 23:41	Re: Does Ansys workbench can import .cdb file as l	#2
prayskyer Guest Posts: n/a	is there anyone help me or give me some advise~~~ thanks a lot~

April 20, 2010, 03:23	same problem	#3
fredcab66 New Member Fred Pier Join Date: Apr 2010 Posts: 5 Rep Power: 5	I have the same problem. I would like to import a .cdb file ( from fluent) in workbench , is it possible? information : it is a 2d problem , i juste want to import pressure on a edge. Thanks! Fred

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How to import Autodesk Inventor .ipt file into ANSYS FLUENT?	soetommy	FLUENT	0	September 27, 2011 00:35
OpenFOAM 1.7.1 installation problem on OpenSUSE 11.3	flakid	OpenFOAM Installation	16	December 28, 2010 08:48
1.7.x Environment Variables on Linux 10.04	rasma	OpenFOAM Installation	9	July 30, 2010 04:43
Compiling gmshFoam with OpenFOAM-1.5	BlGene	Open Source Meshers: Gmsh, Netgen, CGNS, ...	10	August 6, 2009 04:26
PHI file structure	Eugene	Phoenics	9	November 2, 2001 22:00

April 20, 2010, 15:39		#4
stumpy Senior Member Join Date: Apr 2009 Posts: 417 Rep Power: 10	Something like the following Command Snipet in WB should do it: /PREP7 /inp,filename,sfe /SOLVE

April 20, 2010, 15:48		#5
fredcab66 New Member Fred Pier Join Date: Apr 2010 Posts: 5 Rep Power: 5	Thanks Stumpy for your reply . I will try it ! thanks again! Fred

April 24, 2010, 07:24		#6
fredcab66 New Member Fred Pier Join Date: Apr 2010 Posts: 5 Rep Power: 5	Helo stumpy , I have tryed a lot , but i con't import load . Could you explain more your solution please? Whant kind ( and extension) of file can i import? Where do i generate this file ( cfd post, fluent)? I tryed the export from fluent in cdb, but i failed , the Snipet was not enough readable. thanks again! cheers fred

April 26, 2010, 01:43		#7
Ohbuchi Member Masashi Ohbuchi Join Date: Oct 2009 Posts: 64 Rep Power: 5	If you mentioned about cmdb (Meshing) not cdb (Mechanical APDL), you can import by File->import. If your cmdb file contains CFX-Mesh data created by release 10, you should import by release 11 first and save as release 11 data.