CFD Online Discussion Forums

CFD Online Discussion Forums (https://www.cfd-online.com/Forums/)
-   CFX (https://www.cfd-online.com/Forums/cfx/)
-   -   How can I get the CFX technical report (https://www.cfd-online.com/Forums/cfx/26161-how-can-i-get-cfx-technical-report.html)

Lan July 27, 2008 02:55

How can I get the CFX technical report
 
Hi everyone!

I am looking for the CFX technical report "Development and Application of a Zonal DES Turbulence Model for CFX-5 CFX-Validation Report, CFX-VAL17/0503."

How could I get the CFX technical report for can you send me a copy?

Thank you very much!

turbinesv@gmail.com

Rogerio Fernandes Brito July 27, 2008 07:21

Re: How can I get the CFX technical report
 
http://www.sciencedirect.com/science...5b94d9a7150e5b

doi:10.1016/j.firesaf.2006.08.011 Copyright © 2006 Elsevier Ltd All rights reserved. Numerical simulation of backdraft phenomena

Andrej Horvata, and Yehuda Sinai, a,

aANSYS Europe Ltd., West Central 127, Milton Park, OX14 4SA Abingdon, Oxfordshire, UK

Received 21 March 2005; revised 17 August 2006; accepted 30 August 2006. Available online 4 December 2006.

References and further reading may be available for this article. To view references and further reading you must purchase this article.

Abstract This paper reports preliminary computational fluid dynamics (CFD) simulations of backdraft observed in an experimental rig at Lund University. The analysis was performed with the CFX software using the Detached Eddy Simulation (DES) turbulence model, a hybrid of Large Eddy Simulation (LES) and RANS, in combination with the EDM combustion model. The DES model uses a RANS formulation in wall proximity to avoid computationally expensive grid resolution that is necessary for realistic LES predictions in wall layers.

The preliminary results are qualitatively promising. The simulations began at the instant at which the door opens. A stream of fresh and cold air enters the enclosure as a gravity current. In the rig, ignition was triggered by flammable conditions existing at a wire, which was constantly heated. In the CFD model the ignition time is computed automatically when flammability conditions are reached inside the enclosure, at the wire, as part of the analysis. Subsequently, the fire front is formed. The deflagration expels fuel-rich mixture into environment, and the combustion continues outside the enclosure as a typical 'secondary' event. Considering that backdraft is a very complex phenomenon, the outcome is considered by the authors to be encouraging.

Keywords: Backdraft; Fire; Gravity current; CFD; Deflagration; Ignition

or in:

http://linkinghub.elsevier.com/retri...79711206001147

http://www.informaworld.com/index/788588837.pdf

http://epubl.ltu.se/1402-1544/2006/4...DT-0641-SE.pdf


Rogerio Fernandes Brito July 30, 2008 15:23

Re: How can I get the CFX technical report
 
File 0_Numerical_simulation_of_backdraft_phenomena.pdf (508 KB) uploaded!

Thank you for your upload. Remember that only those people are able to access your files knowing the exact link. RapidShare is a file hoster and does not announce your files anywhere.

Your Download-Link #1:

http://rapidshare.de/files/40121485/...omena.pdf.html


Lan July 31, 2008 08:37

Re: How can I get the CFX technical report
 
Thank very much, Rogerio .

Rogerio Fernandes Brito July 31, 2008 09:30

Re: How can I get the CFX technical report
 
You´re welcome!

s.fallah September 12, 2015 10:09

CFX technical and validation report
 
Hi every one!
I am looking for the CFX technical report "Development and Application of a Zonal DES Turbulence Model for CFX-5 CFX-Validation Report, CFX-VAL17/0503."
How could I get the CFX technical report for can you send me a copy?
Given link dose not work.

fallah.saleh@yahoo.com

clj September 27, 2018 20:59

Hi everyone!

I am looking for the CFX technical report "Development and Application of a Zonal DES Turbulence Model for CFX-5 CFX-Validation Report, CFX-VAL17/0503."

How could I get the CFX technical report ,or if anybody can send me a copy?

Thank you very much!:p:p

chenlj0406@163.com;chenlj0406@gmail.com

ghorrocks September 28, 2018 01:18

Contact ANSYS support.


All times are GMT -4. The time now is 02:34.