Transient Thermal Analysis with FSI

December 9, 2008, 00:46

Hi Guys,

As you can see in the previous topic I have created, I have a problem with getting results for the heat transfer part.

http://www.cfd-online.com/Forum/cfx_...cgi?read=25506 http://www.cfd-online.com/Forum/cfx_...cgi?read=21992

These given links and other posts say, that the heat convective and conductive parts are automatically calculated during the solving process.

When I open the calculated rst-file with ANSYS-Post, it only gives me options to visualize structural parameters, e.g. von Mises. How can I visualize temperature, heat flux distributions or thermal stresses within FSI-Simulations? It doesn't appear at all.

http://www.cfd-online.com/Forum/cfx.cgi?read=30133

This the related link this post is refered to. I'm desperate because I can not find out how it works. Thank you for helping!!

Cheers, Abduri

Mechstud · March 25, 2009, 05:53

during ur ansys structural setup, u need to insert thermal condition in ur flexible dynamic model so as to simulate thermal part also after that u can visualise the desired results

Abduri · March 27, 2009, 02:47

Hi,

thanks for your reply. I have done this but I have following problem:

When I do One-Way FSI between ANSYS and CFX, the defined interaction interface within CFX-Pre lets me choose for FORC, DISP, HFLU or TEMP as additional data to be transferred.

When I choose for TEMP, the temperature field from the interface is loaded onto the the solid. But what I would need is the heat flux. So when I switch to HFLU is doesn't calculate any heat flux, the solver just stays at 0 and the solid stays at ambient temperature instead of slowly increasing. Is the CFD solver not calculating any heat flux at the interface?

How can let him transfer heat flux and not temperature?

Please help! I have actually tried everything but nothing worked out.

December 9, 2008, 00:46	Transient Thermal Analysis with FSI	#1
Abduri Guest Posts: n/a	Hi Guys, As you can see in the previous topic I have created, I have a problem with getting results for the heat transfer part. http://www.cfd-online.com/Forum/cfx_...cgi?read=25506 http://www.cfd-online.com/Forum/cfx_...cgi?read=21992 These given links and other posts say, that the heat convective and conductive parts are automatically calculated during the solving process. When I open the calculated rst-file with ANSYS-Post, it only gives me options to visualize structural parameters, e.g. von Mises. How can I visualize temperature, heat flux distributions or thermal stresses within FSI-Simulations? It doesn't appear at all. http://www.cfd-online.com/Forum/cfx.cgi?read=30133 This the related link this post is refered to. I'm desperate because I can not find out how it works. Thank you for helping!! Cheers, Abduri

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FSI Transient Thermal Analysis	Abduri	CFX	1	January 1, 2017 22:54
Transient analysis of particle flow with Fluid-Structure Interaction (FSI)	Julian K.	FLUENT	0	September 14, 2011 15:40
Transient Thermal Analysis in Ansys Workbench	khurram1	ANSYS	0	November 22, 2010 02:40
FSI simulation thermal analysis	Michelle	CFX	2	November 3, 2007 09:15
Short Course: Computational Thermal Analysis	Dean S. Schrage	Main CFD Forum	11	September 27, 2000 17:46

March 25, 2009, 05:53		#2
Mechstud New Member Madhur Bhaiya Join Date: Mar 2009 Posts: 3 Rep Power: 17	during ur ansys structural setup, u need to insert thermal condition in ur flexible dynamic model so as to simulate thermal part also after that u can visualise the desired results

March 27, 2009, 02:47		#3
Abduri New Member Join Date: Mar 2009 Posts: 1 Rep Power: 0	Hi, thanks for your reply. I have done this but I have following problem: When I do One-Way FSI between ANSYS and CFX, the defined interaction interface within CFX-Pre lets me choose for FORC, DISP, HFLU or TEMP as additional data to be transferred. When I choose for TEMP, the temperature field from the interface is loaded onto the the solid. But what I would need is the heat flux. So when I switch to HFLU is doesn't calculate any heat flux, the solver just stays at 0 and the solid stays at ambient temperature instead of slowly increasing. Is the CFD solver not calculating any heat flux at the interface? How can let him transfer heat flux and not temperature? Please help! I have actually tried everything but nothing worked out.