CFD Online Discussion Forums

CFD Online Discussion Forums (http://www.cfd-online.com/Forums/)
-   CFX (http://www.cfd-online.com/Forums/cfx/)
-   -   transient simulation of a rotating rectangle (http://www.cfd-online.com/Forums/cfx/67222-transient-simulation-rotating-rectangle.html)

icesniffer August 7, 2009 11:42

transient simulation of a rotating rectangle
 
hello
i need some help in cfx. I can't do a transient simulation of a simple rectangle rotating by an axys. This are my command lines. im not sure if this is the best option. i want the solid rectangle rotating but not the mesh. the air should only be modified by the rectangle and not by the motion of the domain. that seams no correct to me. thanks to all.

LIBRARY:
MATERIAL: Air at 25 C
Material Description = Air at 25 C and 1 atm (dry)
Material Group = Air Data, Constant Property Gases
Option = Pure Substance
Thermodynamic State = Gas
PROPERTIES:
Option = General Material
Thermal Expansivity = 0.003356 [K^-1]
ABSORPTION COEFFICIENT:
Absorption Coefficient = 0.01 [m^-1]
Option = Value
END
DYNAMIC VISCOSITY:
Dynamic Viscosity = 1.831E-05 [kg m^-1 s^-1]
Option = Value
END
EQUATION OF STATE:
Density = 1.185 [kg m^-3]
Molar Mass = 28.96 [kg kmol^-1]
Option = Value
END
REFERENCE STATE:
Option = Specified Point
Reference Pressure = 1 [atm]
Reference Specific Enthalpy = 0. [J/kg]
Reference Specific Entropy = 0. [J/kg/K]
Reference Temperature = 25 [C]
END
REFRACTIVE INDEX:
Option = Value
Refractive Index = 1.0 [m m^-1]
END
SCATTERING COEFFICIENT:
Option = Value
Scattering Coefficient = 0.0 [m^-1]
END
SPECIFIC HEAT CAPACITY:
Option = Value
Specific Heat Capacity = 1.0044E+03 [J kg^-1 K^-1]
Specific Heat Type = Constant Pressure
END
THERMAL CONDUCTIVITY:
Option = Value
Thermal Conductivity = 2.61E-02 [W m^-1 K^-1]
END
END
END
END
FLOW:
SOLUTION UNITS:
Angle Units = [rad]
Length Units = [m]
Mass Units = [kg]
Solid Angle Units = [sr]
Temperature Units = [K]
Time Units = [s]
END
SIMULATION TYPE:
Option = Transient
EXTERNAL SOLVER COUPLING:
Option = None
END
INITIAL TIME:
Option = Automatic with Value
Time = 0 [s]
END
TIME DURATION:
Option = Total Time
Total Time = 5 [s]
END
TIME STEPS:
Option = Timesteps
Timesteps = 0.0138889 [s]
END
END
DOMAIN: rotor
Coord Frame = Coord 0
Domain Type = Fluid
Fluids List = Air at 25 C
Location = B35
BOUNDARY: Domain Interface 1 Side 1
Boundary Type = INTERFACE
Location = F6.35
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = Conservative Interface Flux
END
TURBULENCE:
Option = Conservative Interface Flux
END
END
END
BOUNDARY: WALL
Boundary Type = WALL
Frame Type = Rotating
Location = back,bottom,front,left,right,top
BOUNDARY CONDITIONS:
WALL INFLUENCE ON FLOW:
Option = No Slip
END
END
END
BOUNDARY: op1
Boundary Type = OPENING
Frame Type = Rotating
Location = topo inf,topo sup
BOUNDARY CONDITIONS:
FLOW DIRECTION:
Option = Normal to Boundary Condition
END
FLOW REGIME:
Option = Subsonic
END
MASS AND MOMENTUM:
Option = Opening Pressure and Direction
Relative Pressure = 1 [atm]
END
TURBULENCE:
Option = Medium Intensity and Eddy Viscosity Ratio
END
END
END
DOMAIN MODELS:
BUOYANCY MODEL:
Option = Non Buoyant
END
DOMAIN MOTION:
Angular Velocity = 1 [rev s^-1]
Option = Rotating
AXIS DEFINITION:
Option = Coordinate Axis
Rotation Axis = Coord 0.2
END
END
MESH DEFORMATION:
Option = None
END
REFERENCE PRESSURE:
Reference Pressure = 1 [atm]
END
END
FLUID MODELS:
COMBUSTION MODEL:
Option = None
END
HEAT TRANSFER MODEL:
Option = None
END
THERMAL RADIATION MODEL:
Option = None
END
TURBULENCE MODEL:
Option = SST
END
TURBULENT WALL FUNCTIONS:
Option = Automatic
END
END
INITIALISATION:
Frame Type = Rotating
Option = Automatic
INITIAL CONDITIONS:
Velocity Type = Cartesian
CARTESIAN VELOCITY COMPONENTS:
Option = Automatic with Value
U = 0 [m s^-1]
V = 0 [m s^-1]
W = 0 [m s^-1]
END
EPSILON:
Option = Automatic with Value
END
K:
Option = Automatic with Value
END
STATIC PRESSURE:
Option = Automatic with Value
Relative Pressure = 1 [atm]
END
END
END
END
DOMAIN: stator
Coord Frame = Coord 0
Domain Type = Fluid
Fluids List = Air at 25 C
Location = B92
BOUNDARY: Domain Interface 1 Side 2
Boundary Type = INTERFACE
Location = F55.92
BOUNDARY CONDITIONS:
MASS AND MOMENTUM:
Option = Conservative Interface Flux
END
TURBULENCE:
Option = Conservative Interface Flux
END
END
END
BOUNDARY: inlet
Boundary Type = INLET
Location = inlet
BOUNDARY CONDITIONS:
FLOW REGIME:
Option = Subsonic
END
MASS AND MOMENTUM:
Normal Speed = 10 [m s^-1]
Option = Normal Speed
END
TURBULENCE:
Option = Medium Intensity and Eddy Viscosity Ratio
END
END
END
BOUNDARY: op2
Boundary Type = OPENING
Location = op,outlet
BOUNDARY CONDITIONS:
FLOW DIRECTION:
Option = Normal to Boundary Condition
END
FLOW REGIME:
Option = Subsonic
END
MASS AND MOMENTUM:
Option = Opening Pressure and Direction
Relative Pressure = 1 [atm]
END
TURBULENCE:
Option = Medium Intensity and Eddy Viscosity Ratio
END
END
END
DOMAIN MODELS:
BUOYANCY MODEL:
Option = Non Buoyant
END
DOMAIN MOTION:
Option = Stationary
END
MESH DEFORMATION:
Option = None
END
REFERENCE PRESSURE:
Reference Pressure = 1 [atm]
END
END
FLUID MODELS:
COMBUSTION MODEL:
Option = None
END
HEAT TRANSFER MODEL:
Option = None
END
THERMAL RADIATION MODEL:
Option = None
END
TURBULENCE MODEL:
Option = SST
END
TURBULENT WALL FUNCTIONS:
Option = Automatic
END
END
END
DOMAIN INTERFACE: Domain Interface 1
Boundary List1 = Domain Interface 1 Side 1
Boundary List2 = Domain Interface 1 Side 2
Interface Type = Fluid Fluid
INTERFACE MODELS:
Option = General Connection
FRAME CHANGE:
Option = Transient Rotor Stator
END
PITCH CHANGE:
Option = Automatic
END
END
MESH CONNECTION:
Option = GGI
END
END
INITIALISATION:
Frame Type = Stationary
Option = Automatic
INITIAL CONDITIONS:
Velocity Type = Cartesian
CARTESIAN VELOCITY COMPONENTS:
Option = Automatic with Value
U = 0 [m s^-1]
V = 0 [m s^-1]
W = 0 [m s^-1]
END
EPSILON:
Option = Automatic with Value
END
K:
Option = Automatic with Value
END
STATIC PRESSURE:
Option = Automatic with Value
Relative Pressure = 1 [atm]
END
END
END
OUTPUT CONTROL:
RESULTS:
File Compression Level = Default
Option = Essential
END
TRANSIENT RESULTS: Transient Results 1
File Compression Level = Default
Option = Smallest
OUTPUT FREQUENCY:
Option = Every Timestep
END
END
END
SOLVER CONTROL:
ADVECTION SCHEME:
Option = High Resolution
END
CONVERGENCE CONTROL:
Maximum Number of Coefficient Loops = 15
Minimum Number of Coefficient Loops = 3
Timescale Control = Coefficient Loops
END
CONVERGENCE CRITERIA:
Residual Target = 1e-04
Residual Type = RMS
END
TRANSIENT SCHEME:
Option = Second Order Backward Euler
TIMESTEP INITIALISATION:
Option = Automatic
END
END
END
END
COMMAND FILE:
Version = 11.0
Results Version = 11.0
END
EXECUTION CONTROL:
INTERPOLATOR STEP CONTROL:
Runtime Priority = Standard
EXECUTABLE SELECTION:
Double Precision = Off
END
MEMORY CONTROL:
Memory Allocation Factor = 1.0
END
END
PARALLEL HOST LIBRARY:
HOST DEFINITION: c2s03m10
Remote Host Name = C2-S03-M10
Host Architecture String = intel_xeon64.sse2_winnt5.1
Installation Root = C:\Program Files\ANSYS Inc\v%v\CFX
END
END
PARTITIONER STEP CONTROL:
Multidomain Option = Independent Partitioning
Runtime Priority = Standard
EXECUTABLE SELECTION:
Use Large Problem Partitioner = Off
END
MEMORY CONTROL:
Memory Allocation Factor = 1.0
END
PARTITIONING TYPE:
MeTiS Type = k-way
Option = MeTiS
Partition Size Rule = Automatic
END
END
RUN DEFINITION:
Definition File = C:\Documents and \
Settings\em14063\Desktop\rectangulo1transiente5s.d ef
Interpolate Initial Values = Off
Run Mode = Full
END
SOLVER STEP CONTROL:
Runtime Priority = Standard
EXECUTABLE SELECTION:
Double Precision = Off
END
MEMORY CONTROL:
Memory Allocation Factor = 1.0
END
PARALLEL ENVIRONMENT:
Number of Processes = 1
Start Method = Serial
END
END
END

Missing K initial condition CCL; using Automatic
Missing Epsilon initial condition CCL; using Automatic
Missing K initial condition CCL; using Automatic
Missing Epsilon initial condition CCL; using Automatic

ghorrocks August 8, 2009 07:25

Can you post an image explaining what you are trying to do?


All times are GMT -4. The time now is 16:24.