
[Sponsors] 
March 18, 2010, 13:32 
CFX Treatment of Laminar and Turbulent Flows

#1 
Senior Member
Join Date: Feb 2010
Posts: 145
Rep Power: 8 
I have not received a consistent answer and am hoping to get come clarification from this forum.
I am simulating air flow through a duct. The air flows through a constantarea duct, then through a series of fins and then through a constantarea duct similar to the upstream section. By a standard Reynolds number calcuation with hydraulic diameter, the flow upstream and downstream would be turbulent and the flow between the fins would be laminar. The duct is 1.5" wide by 0.35" tall. Perhaps the shape of the duct has something to do with the stability of the flow. I have several questions with regard to CFX's treatment of this flow. I am new to CFX and also to turbulence, so please feel free to provide as basic an answer as necessary, as if explaining to a beginning mechanical engineering student. Please feel free to answer all or any part of my questions, as I am asking a lot! How does CFX treat this problem if the flow is actually turbulent but the laminar option is specified? How does CFX treat this problem if the flow is actually laminar but the turbulent option is specified? What happens if part of the flow is laminar and part is turbulent? An ANSYS CFX consultant says that the Reynolds number calculation is based on the cubed root of the volume, that CFX does not calculate some instability in the flow to determine whether the flow is laminar or turbulent, and that the warning message is purely based on this Reynolds number which may not be meaningful. This consultant's advice seemed the most reasonable to me compared with everything else that I have been told. However, this would not explain one thing  it seemed that as the mesh became finer, the warning that the flow may be turbulent when the laminar option was set. Any explanation? I thought that the solution may have detected the the flow never becomes unsteady or turbulent with the finer mesh but apparently CFX does not try to calculate this. Also, a colleague of mine asks: We know the flow is (or rapidly becomes) laminar in the fin section based on a Reynolds for that region of 1000. The fin section is where we are interested in determining heat transfer (and pressure drop). How does a solution setting of turbulent capture the fact that the flow is laminar? Will it converge? How accurate will it be compared to a laminar setting? Wouldn’t we come closer to what we are seeking by using a laminar setting? Further, the correlations we are comparing to are based on laminar flow. Thank you very much for any information! Help would be most gratefully appreciated. Last edited by Jade M; March 18, 2010 at 14:30. Reason: Typo 

March 18, 2010, 18:01 

#2  
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 11,084
Rep Power: 86 
Quote:
Quote:
The comments by the CFX consultant is correct. The reported Re is just a guide and is only useful to check you are in the ball park. If you want a more representative Re you should calculate it yourself using an appropriate length, velocity, viscosity and density scale. Finer meshes have reduced numerical dissipation and therefore capture more fow features. This means a simulation on a coarse grid with a laminar model may be steady, but with grid refinement goes unsteady. This was not "detected" by CFX, it is just a fact that the numerical dissipation has reduced sufficiently that the transient features are not damped out. Quote:
Quote:


March 19, 2010, 11:05 
Thank you!

#3 
Senior Member
Join Date: Feb 2010
Posts: 145
Rep Power: 8 
I appreciate your detailed comments. This really helps!


January 8, 2013, 09:41 

#4 
New Member
william moore
Join Date: Jan 2013
Posts: 8
Rep Power: 4 
Based on my experience with Fluent the komega SST model at least exhibits better convergence behavior for cases in which there is both fully laminar and turbulent flow in the same fluid domain, provided that there is sufficient resolution of the boundary layer and appropriate yplus values.
Howver this does not necessarily mean that the komega SST model is more accurate than the kepsilon models unless verified by test data. One option worth trying would be to beraek the fluid domain into separate zones (laminar and turbulent) and use a turbulence model but specify a laminar flow model for the fluid zone which is known to be laminar. One peculiarity we have observed is that when we apply a mass flow inlet with a secondary species defined, the komega model gives a huge mass imbalance for the secondary species after a few hundred iterations, which does not occur when we use the kepsilon models. Has anyone else observed this behavior with komega model? 

January 8, 2013, 18:17 

#5 
Super Moderator
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 11,084
Rep Power: 86 
If you have turbulence transition in a model then that sounds like a case for the turbulence transition model. Then there is no need for defining different domains, and then linking them together somehow (I do not know how you would do this  it sounds very dodgy to me).


January 8, 2013, 18:45 

#6 
New Member
william moore
Join Date: Jan 2013
Posts: 8
Rep Power: 4 
Excellent point! The komega model works very well but our species mass balance was totally wrong for some reason. We are currently using the kepsilon realizable model with enhanced wall treatment and refined boundary mesh. It is converging well after 50 iterations but due to the size of the model (16 million cells) it will take sevral hundred or more iterations. I wish I knew why the secondary species mass balance was so far out of balance for the komega model and not the other turbulence models.


January 26, 2013, 11:11 

#7 
New Member
william moore
Join Date: Jan 2013
Posts: 8
Rep Power: 4 
Having done some more testing we discovered that we were using the wrong type of boundary condition to model the trace secondary species input into the flow domain. Rather than using a fixed mass flow inlet we chose to use volumetric mass generation as a source term by creating a separate volume next to the large fluid domain. Now when we use komega SST model the trace secondary species mass convergence is completely satisfied. This also required using a boundary layer mesh with a wall y plus very close to 1. The komega model appears to be predicting the correct flow pattern and velocity vector profile even though our model contains both fully turbulent and laminar flow.
William 

Thread Tools  
Display Modes  


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
Laminar doesn't converge; Turbulent models do?  Amit  FLUENT  11  April 23, 2015 22:55 
Using a turbulent model when the flow is entirely laminar.  mwhyte  FLUENT  1  June 7, 2012 10:35 
[GAMBIT] 3D Boundary Layer Laminar and Turbulent meshing  Harald D  ANSYS Meshing & Geometry  1  July 7, 2009 06:20 
Half laminar and turbulent model trying to solve  Andrew Clarke  FLUENT  5  May 19, 2008 13:40 
Transition from laminar to turbulent flows  Rob  FLUENT  5  January 10, 2002 17:17 