CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > CFX

Solver exit return code 1

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   May 31, 2010, 10:41
Default Solver exit return code 1
  #1
New Member
 
Auristela Vasquez
Join Date: May 2010
Posts: 2
Rep Power: 0
acvq is on a distinguished road
HI!!

i have a problem with the solver cfx. when i am running a simulation, it stops and appears this
================================================== ====================
OUTER LOOP ITERATION = 43 ( 12) CPU SECONDS = 6.268E+03 (2.567E+03)
----------------------------------------------------------------------
| Equation | Rate | RMS Res | Max Res | Linear Solution |
+----------------------+------+---------+---------+------------------+
+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX solver exited with return code 1. No results file |
| has been created.

Can anyone help me??

Regards!!!!!
acvq is offline   Reply With Quote

Old   June 1, 2010, 03:39
Default
  #2
New Member
 
Daniel Paukner
Join Date: Apr 2010
Posts: 17
Rep Power: 7
Pocket is on a distinguished road
First of all, post a bit more information.

This error basically doesn't tell you anything.

Did your simulation diverge?
Check the "Rate" of the previous iterations. It should be lower than 1 (can be a little over 1 and its not a problem), if its significantly bigger than 1, it's diverging fast.

Did the linear solver fail?
Check whether there is OK, ok, F or * in "Linear Solution"
if F or *, that's most likely your culprit.

But give more information. Static or transient? Is it a iteration where a load is applied? Mesh movement?
Pocket is offline   Reply With Quote

Old   June 1, 2010, 04:09
Default
  #3
New Member
 
Auristela Vasquez
Join Date: May 2010
Posts: 2
Rep Power: 0
acvq is on a distinguished road
HEllo!

The simulation is a steady-state calculation of a multiphase-flow ejector without mesh movement.

When the simulation ends with errors, both the numerical solution and the rate are good. The numerical solution is "OK" and the rate is less than one. But the solver stop and return with the code 1, i don't know this error.

What do you think??

THANK YOU VERY MUCH

REGARDS
acvq is offline   Reply With Quote

Old   June 1, 2010, 04:17
Default
  #4
Senior Member
 
Attesz's Avatar
 
Attesz
Join Date: Mar 2009
Posts: 355
Rep Power: 8
Attesz is an unknown quantity at this point
what about your mesh quality? expansion factors etc?
Attesz is offline   Reply With Quote

Old   August 29, 2010, 16:22
Default the code 1
  #5
New Member
 
caesar
Join Date: Aug 2010
Posts: 1
Rep Power: 0
caesar is on a distinguished road
HELLO...!!!!

I have the similar problem....

So, what did you do to fix that?

Many thanks............!!!!!
caesar is offline   Reply With Quote

Old   September 11, 2011, 09:06
Default
  #6
New Member
 
M. A.
Join Date: Jul 2010
Posts: 27
Rep Power: 7
motahar is on a distinguished road
Hi friends,

I'm simulating a simple tube in 2-phase, using Droplets.
I've experienced the same problem.

Can a friend help me?

Thanks
motahar is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Disabling and Enabling Solver Summary Outputs within code adona058 OpenFOAM Running, Solving & CFD 3 November 1, 2007 12:00
Solver error with return code 137 (CFX10 in Linux) JamesH CFX 0 January 25, 2006 06:54
Solver quits without results saying Return Code 15 Kramer CFX 6 May 6, 2005 04:02
Setting a B.C using UserFortran in 4.3 tokai CFX 10 July 17, 2001 16:25
Open source CFD code development, possible? Dr. Yazid Bindar Main CFD Forum 27 July 18, 2000 00:18


All times are GMT -4. The time now is 01:14.