CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

Conjugate Heat Transfer of Motorized EGR

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   October 12, 2010, 02:21
Default Conjugate Heat Transfer of Motorized EGR
  #1
Member
 
Venkat
Join Date: Nov 2009
Posts: 35
Rep Power: 16
enr_venkat is on a distinguished road
Dear all,

I'm currently working on a Motorized EGR project. The device is used in automotive exhaust systems to reduce NOx emissions. When combustion temperatures are high (2200 C), the EGR will be operated for certain cycles by recirculating exhaust gases back to the inlet manifold of an engine which dilutes the incoming air to the engine which consequently reduces the combustion temperature in the engine thus controlling NOx emissions.

I would like to predict the conjugate heat transfer of the EGR valve. The plunger in the valve is operated by a stepper DC motor with some plastic gears that drives the cam and camshaft. Following are the steps considered for CFD Modeling of the EGR valve

1. Extracted fluid volume from the solid body using ANSYS DesignModeler in ANSYS Workbench 12.1

2. Different solid parts were treated individually in the ANSYS Workbench 12.1 i.e. meshing individually for moderate mesh quality (skewness - 0.7-0.85) eg: piston assembly, metallic bush, oil seal etc.,.

3. Linked all mesh cells in Workbench to CFX Pre- setup cell. When CFX is edited, i can find all the components get connected

For choosing the flow model in steady state CFD analysis, i've considered Total Energy model and Fluid Discrete Transfer Media Radiation model as the Mach number exceeds 0.2 in compressible flows. Moreover the inlet exhaust temperature of the gas is around 1023 K. I've created Fluid solid interface between the fluid domain and the first point of contact i.e. Piston assembly and then i did Solid-solid interface for every part that is in contact with each other including bush, oil seal, plastic gears, dc motor, etc.,. My main objective is to study the effect of exhaust gas temperature on solid parts and determine the heat transfer at desired locations. For instance, selection of material for oil seal was challenging i.e. engineers don't know how much temperature propagates if different sets of oil seal materials are tried. FKM Seal cannot resist temperatures exceeding 250 C.

I would like to know whether my modeling approach is correct or is there anything else has to be considered for the analysis. Any suggestions or help from CFD Expertise is highly appreciated

Many thanks
enr_venkat is offline   Reply With Quote

Old   October 12, 2010, 19:17
Default
  #2
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,665
Rep Power: 143
ghorrocks is just really niceghorrocks is just really niceghorrocks is just really niceghorrocks is just really nice
Are you sure this can be done as a steady state analysis? The flow is going to be very fast, pulses at 10Hz or 100Hz or something like that and I doubt it will have time to get to thermal equilibrium. Alternately you could look for some sort of pseudo-steady state by getting the average conditions but this is an inaccurate approach as the heat transfer coefficients will change with flow rate too so averaging it all back to a pseudo-steady flow could be a problem.
ghorrocks is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Convective / Conductive Heat Transfer in Hypersonic flows enigma Main CFD Forum 2 November 1, 2009 23:53
Conjugate heat transfer problem hvem10 FLUENT 2 October 29, 2009 18:31
Conjugate heat transfer and radiation modeling questions shankara.2 FLUENT 0 April 21, 2009 16:55
Conjugate heat transfer with periodic boundaries Suresh FLUENT 0 February 23, 2009 10:51
Convective Heat Transfer - Heat Exchanger Mark CFX 6 November 15, 2004 16:55


All times are GMT -4. The time now is 09:02.