CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > CFX

1 Was FSI for a flow over a cylinder

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   February 28, 2011, 13:51
Default 1 Was FSI for a flow over a cylinder
  #1
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
Hello,

I need help with this as I am stuck on this for a long time now. I am trying to find out the displacement of a cylinder in a cross flow. The cylinder is subjected to move in the transverse direction only. I am not getting correct displacements of the cylinder. I am using a CEL expression for Mesh deformation.
To check my mesh and BC, I tried to run a transient case of a flow over a fixed cylinder and compared the results. They were alright. That means the Mesh, Boundary layer, physics of the problem, Boundary conditions are all fine. But when I use this mesh deformation, I cannot validate my results.

My geometry simple. It is just a square domain with a circle at the centre (i.e 2-D)


The CEL expression is very much similar to the CEL expression given in the tutorial Ch: 22 Fluid Struct interaction and mesh deformation.

The only difference is that the tutorial has a spring while I also have a damper with the spring.

I am attaching the pic of the mesh and the CEL expression am using.

Any kind of suggestion is highly appreciated. Thank you.

boundary layer.jpg

mesh1.jpg

CELexpression.txt
vmlxb6 is offline   Reply With Quote

Old   February 28, 2011, 15:59
Default
  #2
Member
 
Join Date: Dec 2009
Posts: 44
Rep Power: 16
cfdgremlin is on a distinguished road
I've done very similar calculations for turbulent flow, with some reasonable results.

Are the forces on the cylinder what you expect for the flow Reynolds Number? If they are in the right ball park, then it is a simple matter to calculate the free undamped vibration amplitude and compare it with what you get out of CFX. This will at least tell you if your expression formulation is right.
cfdgremlin is offline   Reply With Quote

Old   February 28, 2011, 16:07
Default @ cfdgremlin
  #3
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
I have not compared the forces yet. What I presumed was that the displacements were low bcoz of low forces. Is there any papers/txt book etc with which I can compare my force data for a moving cylinder, to see if ???
I guess the forces on the stationary cylinder will be different from that of a moving cylinder.
I tried running a stationary cylinder case (which did not involve FSI-mesh motion), and the forces/lift coeff were correct.

Thank you for writing !!!

Regards,

Prof. Chaos
vmlxb6 is offline   Reply With Quote

Old   March 1, 2011, 18:20
Default
  #4
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,665
Rep Power: 143
ghorrocks is just really niceghorrocks is just really niceghorrocks is just really niceghorrocks is just really nice
Have you done all the normal sensitivity checks? Mesh, time step, convergence?
ghorrocks is offline   Reply With Quote

Old   March 1, 2011, 18:30
Default
  #5
Senior Member
 
Edmund Singer P.E.
Join Date: Aug 2010
Location: Minneapolis, MN
Posts: 511
Rep Power: 20
singer1812 is on a distinguished road
You can apply the motion to either a subdomain or the walls for this type of problem. Using a subdomain allows you to push the deformed mesh into a region that is better able to handle it. If you dont expect a large deformation, by all means move the walls.

Havent checked your ccl expressions but they should boil down to

a=F/m

after manipulation:

dCYLINDERNew=(velCYLINDEROld+F/mCYLINDER*tstep)*tstep+dCYLINDEROld

I think F in your case should be

FFLow-C*velCYLINDEROld-k*dCYLINDEROld

Which I dont have time to check if all this boils down to what you had in your num/dem ccl.

You should monitor, at the very least, the following values to see if they make sense:

FFLow
C*velCYLINDEROld
k*dCYLINDEROld

And with the equations above mesh motion should be defined as Specified Displacement
singer1812 is offline   Reply With Quote

Old   March 3, 2011, 04:19
Default @ Ghorocks & singer 1812
  #6
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
I used the same mesh to simulate the lift forces over a stationary cylinder. And it gave correct results. Doesn't that mean that the mesh is fine ???

The problem could be when the mesh deforms. The boundary layer near the cylinder walls also deform thus giving wrong results. (I dont know, Its just a wild guess.)

Am using Mesh stiffness to increase near small volumes & stiffness model exponent = 2. Can that cause a problem ???
Should I be using 'increase near boundaries' ???

@ Ghorocks: The solution seems to be converging. The time step is small enough. The RMS courant is close to 0.22 & max courant is 0.7

How to check if the mesh is fine. My mesh is certainly fine for a transient stationary case. But how do I find out the same for a moving mesh ???

@singer: The cylinder wall does have specified displacement. How do I know if Fflow, C*vel or K*disp makes sense ???
vmlxb6 is offline   Reply With Quote

Old   March 3, 2011, 10:30
Default
  #7
Senior Member
 
Edmund Singer P.E.
Join Date: Aug 2010
Location: Minneapolis, MN
Posts: 511
Rep Power: 20
singer1812 is on a distinguished road
You are to decide if they make sense or not.

Are you starting this from a solution interpolated from the non-moving mesh solution? Perhaps, FFLow should be close to the value from that, near the beginning for solution.

At the start of solution I would guess that the spring and damping term should be small, and if the cylindar continues to not move much, should balance out FFlow. If that is not the case, maybe you have something messed up in your logic.
singer1812 is offline   Reply With Quote

Old   March 4, 2011, 10:25
Default @ Ghorocks & singer 1812
  #8
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
1. For a flow over a (moving) cylinder. If I scale my force i.e multiply by the length, should the 2-D case give the same result as that of a 3-D case.

2. For a transient case simulation, is 10^-4 a good convergence criteria ??? Or should I be reducing further.

Thank you.

Last edited by vmlxb6; March 6, 2011 at 16:27.
vmlxb6 is offline   Reply With Quote

Old   March 6, 2011, 18:10
Default
  #9
Super Moderator
 
Glenn Horrocks
Join Date: Mar 2009
Location: Sydney, Australia
Posts: 17,665
Rep Power: 143
ghorrocks is just really niceghorrocks is just really niceghorrocks is just really niceghorrocks is just really nice
Quote:
For a transient case simulation, is 10^-4 a good convergence criteria ??? Or should I be reducing further.
That is a good starting point but you need to prove it is OK for your situation with a sensitivity study.
ghorrocks is offline   Reply With Quote

Old   March 6, 2011, 18:44
Default
  #10
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
Thanks Ghorrocks
vmlxb6 is offline   Reply With Quote

Old   March 15, 2011, 08:11
Default
  #11
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
Hello,

I have run out of options. I have been trying this for a long time now but unable to match experimental values. Can anyone please have a look at my files as I have reached the dead end.

Thank you.
vmlxb6 is offline   Reply With Quote

Old   March 15, 2011, 14:49
Default
  #12
Member
 
Join Date: Dec 2009
Posts: 44
Rep Power: 16
cfdgremlin is on a distinguished road
Can I ask just a couple more questions:

1. Is this a laminar or turbulent flow simulation?

2. What are the details of the experiment? Are the results from a published paper? What are the end-load conditions? Is it a rigid or flexible cylinder? What fluid is used? etc ...

3. How far out are the displacements in the simulation compared to the experiment? Is it a factor of 2, 10, 100?

Thanks
cfdgremlin is offline   Reply With Quote

Old   March 15, 2011, 15:29
Default
  #13
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
Hey,

1. The experiments were run at Re = 525. Hence Laminar.

2. End load conditions ????? I have no idea

3. It is a rigid body

4. Published in Journal of fluid & structures

They are getting A/D = 0.06 while am getting it as 0.03~0.04. In the CEL expression that I have attached, I have used a first order accurate forward differencing scheme. That may be the reason. I dont know it yet. Am still figuring it out.

Thank you for responding.
vmlxb6 is offline   Reply With Quote

Old   March 16, 2011, 12:17
Default
  #14
Member
 
Join Date: Dec 2009
Posts: 44
Rep Power: 16
cfdgremlin is on a distinguished road
Are you able to reveal the details of the paper (name, author, date)?
cfdgremlin is offline   Reply With Quote

Old   March 16, 2011, 12:50
Default
  #15
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
Name: On the maximum amplitude for a freely vibrating cylinder in cross-flow

Author: J.T. Klamo, A. Leonard, A.Roshko

Journal: Journal of Fluids & structures 21(2005) 429-434
vmlxb6 is offline   Reply With Quote

Old   March 21, 2011, 13:35
Default
  #16
Member
 
Join Date: Dec 2009
Posts: 44
Rep Power: 16
cfdgremlin is on a distinguished road
I have only been able to read the abstract, but the authors are well renowned in the field.

In the simulations I have performed, both with using CEL expressions and 2-way FSI with ANSYS, it has been difficult to exactly match the experimental data (although mine were at higher Reynolds numbers). The maximum amplitude usually occurs at "lock-in", and this phenomena is associated with a sharp jump in amplitude ratio.

I would recommend that you perform a number of simulations either side of your targeted conditions to see how the amplitude responds.

Hope this helps.
cfdgremlin is offline   Reply With Quote

Old   March 21, 2011, 14:05
Default
  #17
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
How are you doing a 2-way FSI ??? Does that mean that your Cylinder is deforming ?????

Can I have a look at your CEL expression ??? What discretization scheme are you using ???

Thanks
vmlxb6 is offline   Reply With Quote

Old   May 16, 2011, 03:29
Default @ cfdgremlin
  #18
Senior Member
 
Ugly Kid Joe
Join Date: Aug 2010
Posts: 193
Rep Power: 15
vmlxb6 is on a distinguished road
Hey,

You mentioned that you used a CEL as well as a 2 way FSI. My question is, was the 2 way used to find the structural deformation of the cylinder ???

Thank you.
vmlxb6 is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
benchmark: flow over a circular cylinder goodegg Main CFD Forum 12 January 22, 2013 12:47
reference calcultion, flow around a cylinder butch85 Main CFD Forum 3 January 31, 2011 17:10
Flow over a flat plate & Flow over a cylinder cfdxue Main CFD Forum 0 November 27, 2007 00:26
Anybody knows smth abt the flow around a cylinder? Wenxuan Main CFD Forum 3 March 20, 2007 17:19
Flow over a cylinder Anna Main CFD Forum 9 March 24, 2006 15:32


All times are GMT -4. The time now is 05:05.