CFX solver problem, ERROR #001100279

gooya_kabir · February 4, 2012, 10:15

Hello,
I run a multiphase model, continuous water with dispersed solid. transient mode and particle model were selected. after running it, it doesn't solve at all and stop in the first step. the following message appear:
ERROR #001100279 has occurred in subroutine ErrAction. |
| Message: |
| Stopped in routine GET_GVAR |
| |
| |
| |
| |
| |
+--------------------------------------------------------------------+
+--------------------------------------------------------------------+
| An error has occurred in cfx5solve: |
| |
| The ANSYS CFX solver exited with return code 1. No results file |
| has been created.
I changed the mesh characteristics and timesteps to 0.00001 s, but it doesn't work.

would you guide me in this problem?

thanks a lot for your time

ghorrocks · February 5, 2012, 17:22

There is an error in your setup. You are not defining somthing which is required.

gooya_kabir · February 6, 2012, 03:40

As you told, I check the all models, except one case, nothing was wrong.
:in
A.NSYS C.FX-Pre U.ser's G.uide | D.omains | U.ser I.nterface | Surface Tension Force Model
has come that: You must also specify a Surface Tension Coefficient and select the Primary Fluid. but there is no surface tension coefficient in fluid pair models or elsewhere!!!!
what's wrong do you think?

ghorrocks · February 6, 2012, 19:07

Have you done the tutorials on multiphase flow? That shows you how to set these simulations up.

gooya_kabir · February 7, 2012, 02:55

there is no tutorial for dispersed solid!!!
would you tell me that should set a surface tension coefficient in dispersed solid? there is no empty box for it!!!
it maked me crazy

gooya_kabir · February 7, 2012, 03:01

would you give me an example, address of site or send it to me

Suman Sapkota · May 24, 2018, 05:15

Hello,
I am not sure if it is relevant now. But anyways, I encountered the same problem and I changed the particle solid to user from the material group. the problem is gone.

The particle solid specifies the thermodynamic property of the dispersed phase as solid but when user defined, we can do that by choosing pure substance and thermodynamic property as solid. From this option, we don't need to input surface tension coefficient and the problem vanishes.

February 4, 2012, 10:15	CFX solver problem, ERROR #001100279	#1
gooya_kabir Member Reza Join Date: Feb 2012 Posts: 67 Rep Power: 14	Hello, I run a multiphase model, continuous water with dispersed solid. transient mode and particle model were selected. after running it, it doesn't solve at all and stop in the first step. the following message appear: ERROR #001100279 has occurred in subroutine ErrAction. \| \| Message: \| \| Stopped in routine GET_GVAR \| \| \| \| \| \| \| \| \| \| \| +--------------------------------------------------------------------+ +--------------------------------------------------------------------+ \| An error has occurred in cfx5solve: \| \| \| \| The ANSYS CFX solver exited with return code 1. No results file \| \| has been created. I changed the mesh characteristics and timesteps to 0.00001 s, but it doesn't work. would you guide me in this problem? thanks a lot for your time

February 6, 2012, 03:40	User guide problem	#3
gooya_kabir Member Reza Join Date: Feb 2012 Posts: 67 Rep Power: 14	As you told, I check the all models, except one case, nothing was wrong. :in A.NSYS C.FX-Pre U.ser's G.uide \| D.omains \| U.ser I.nterface \| Surface Tension Force Model has come that: You must also specify a Surface Tension Coefficient and select the Primary Fluid. but there is no surface tension coefficient in fluid pair models or elsewhere!!!! what's wrong do you think?

February 7, 2012, 02:55	I did all!!!	#5
gooya_kabir Member Reza Join Date: Feb 2012 Posts: 67 Rep Power: 14	there is no tutorial for dispersed solid!!! would you tell me that should set a surface tension coefficient in dispersed solid? there is no empty box for it!!! it maked me crazy

February 7, 2012, 03:01	help	#6
gooya_kabir Member Reza Join Date: Feb 2012 Posts: 67 Rep Power: 14	would you give me an example, address of site or send it to me

May 24, 2018, 05:15	same problem but solved	#7
Suman Sapkota Member Suman Sapkota Join Date: Feb 2018 Posts: 32 Rep Power: 8	Hello, I am not sure if it is relevant now. But anyways, I encountered the same problem and I changed the particle solid to user from the material group. the problem is gone. The particle solid specifies the thermodynamic property of the dispersed phase as solid but when user defined, we can do that by choosing pure substance and thermodynamic property as solid. From this option, we don't need to input surface tension coefficient and the problem vanishes.

February 5, 2012, 17:22		#2
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	There is an error in your setup. You are not defining somthing which is required.

February 6, 2012, 19:07		#4
ghorrocks Super Moderator Glenn Horrocks Join Date: Mar 2009 Location: Sydney, Australia Posts: 17,703 Rep Power: 143	Have you done the tutorials on multiphase flow? That shows you how to set these simulations up.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CFX solver problem	Lamine	CFX	4	June 14, 2013 17:43
Working directory via command line	Luiz	CFX	4	March 6, 2011 20:02
ERROR #002100056 CFX FSI problem	Hongdao	CFX	0	November 10, 2010 03:58
CFX Solver Memory Error	mike	CFX	1	March 19, 2008 07:22
CFX new user, problem with solver and PRE settings	Vijesh Joshi	CFX	1	March 13, 2006 22:42