CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > FloEFD, FloWorks & FloTHERM

Bulk averaged values on a surface plane other than the inlet or outlet planes..How??

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   August 11, 2014, 22:13
Default Bulk averaged values on a surface plane other than the inlet or outlet planes..How??
  #1
Member
 
Nikesh Bhattarai
Join Date: Nov 2011
Location: Sacheon, South Korea
Posts: 82
Rep Power: 13
nikesh is an unknown quantity at this point
Hi Boris,
Is it possible to obtain the bulk averaged values on a surface plane other than the inlet or outlet planes (lids)?
On my valve flow case, I want to obtain average pressure and velocity on a surface plane certain distance away from the center of the valve (on both the sides, upstream and downstream direction). And these planes are not the inlet or outlet planes. See the figure attached.
I'm still trying to figure it out, but in vain.
Any help appreciated.
Thanks
Nikesh.
Attached Images
File Type: jpg crossSectionalPlanes.JPG (15.8 KB, 11 views)
nikesh is offline   Reply With Quote

Old   August 14, 2014, 10:28
Default
  #2
Disabled
 
Join Date: Jul 2009
Posts: 616
Rep Power: 23
Boris_M will become famous soon enough
Hi Nikesh,

Yes, you simply add another lid at that position and use the component control to deactivate it for the flow. You can still apply goals on that or surface parameters and get the data you want to know. It is wise to increase the mesh in these lids as the fluid cells are often not that fine and would create a larger interpolation error.

By the way, did you send me your task via email already?

Regards,
Boris
Boris_M is offline   Reply With Quote

Old   August 17, 2014, 07:02
Default
  #3
Member
 
Nikesh Bhattarai
Join Date: Nov 2011
Location: Sacheon, South Korea
Posts: 82
Rep Power: 13
nikesh is an unknown quantity at this point
Hi Boris,
This is the process that has to be applied before running the simulations, right? Is there a way to do so after simulations have been completed? I wish to check various parameters at different cross sections for the cases that have already been run and completed, but I have not created such lids at those positions.

Ah yes I had sent you an email few weeks ago, but I got an automated reply stating that you were on vacation. I could send it to you again after few updates in a couple of days if u r still up?

Thanks,
Nikesh.
nikesh is offline   Reply With Quote

Old   August 18, 2014, 04:06
Default
  #4
Disabled
 
Join Date: Jul 2009
Posts: 616
Rep Power: 23
Boris_M will become famous soon enough
Hi Nikesh,
Well if you want to apply a finer mesh at these sections then you would need to mesh and run it again or at least continue to run it on the old results but you should be able to add these lids afterwards too and use them for the surface parameter feature. It should work as you only need a reference geometry but it might be a little inaccurate compared to a finer mesh version.

Ok, it seems that your email was accidently caught by the spam filter. Let me know when you sent it the next time so I can check if it got filtered again.

Boris
Boris_M is offline   Reply With Quote

Old   August 18, 2014, 22:16
Default
  #5
Member
 
Nikesh Bhattarai
Join Date: Nov 2011
Location: Sacheon, South Korea
Posts: 82
Rep Power: 13
nikesh is an unknown quantity at this point
Boris,
But I can create lid only at the pipe opening, not somewhere in the middle of the pipe.....
Or perhaps there is another way??
nikesh is offline   Reply With Quote

Old   August 19, 2014, 02:42
Default
  #6
Disabled
 
Join Date: Jul 2009
Posts: 616
Rep Power: 23
Boris_M will become famous soon enough
Yes, the create lids tool is supposed to be used for closing the goemetry for internal analysis and only works on planar surfaces where it recognises any holes in it but it won't work within a pipe at a certain location. For that you can either create one at the opening of the pipe and then move it to the location you want it to be via the CAD constraints or you can create some manually at these locations by putting a parallel plane to the opening to the location you want it to be and simply start with a sketch and extrude it.

Boris
Boris_M is offline   Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
flow around a circular cylinder with velocity inlet and outflow outlet shuoxue OpenFOAM 1 March 3, 2014 11:42
pump outlet pressure higher than inlet pressure jstan3 FLUENT 14 February 14, 2014 00:44
flow around a circular cylinder with velocity inlet and outflow outlet shuoxue OpenFOAM Running, Solving & CFD 0 November 2, 2013 05:32
define BCs at inlet and outlet for natural ventilation simulation jjz2013 Main CFD Forum 0 January 29, 2013 16:50
VOF Outlet boundary condition in cfd - ace JM Main CFD Forum 0 December 15, 2006 09:07


All times are GMT -4. The time now is 01:42.