general introduction for customizing flow3d with fortran routines

jk75 · November 23, 2009, 03:11

Hi all,

I've read the manual chapters concerning customizing flow3d using fortran subroutines and became curious about the possibilities this customization might offer. But though I'm experienced in programming c++, I'm an absolute newbie to fortran.
So I was wondering if there is somewhere a general introduction/tutorial/or something like that to help me understand what can be done by this customization (e.g. with variables are accessable,...) and how this is done (e.g. additional simple codes like those in the manual...).

Many thanks in advance and best regards,
Johannes

MuxaB · November 29, 2009, 19:09

Johannes,

There is not much more written on this beyond what is described in the FLOW-3D manual and in the comments within the customizable subroutines and functions.

It would be easier to first figure out what you are trying to achieve by customizing FLOW-3D to point you in the right direction.

Michael

therockyy · February 10, 2010, 16:18

Programming in Fortran is relative easy if you have background using C++.
You can follow the manual to call the modules and include other variables.

I think the most difficult question is how to link your customizations and make Flow-3D to response to them. You need to change the Makefiles.

huanglin8545 · May 20, 2012, 23:05

Quote:

Originally Posted by therockyy

Programming in Fortran is relative easy if you have background using C++.
You can follow the manual to call the modules and include other variables.

I think the most difficult question is how to link your customizations and make Flow-3D to response to them. You need to change the Makefiles.

Dear therockyy,
You said that the most difficult question is how to link your customizations and make Flow-3D to response to them. You need to change the Makefiles.Now I faced with the problem and don't konw how to link customizations and make Flow-3D to response to them .How can I change the Makefiles?Just use IVF9.1 and VS2005?Could you help me?Thanks

MuxaB · May 22, 2012, 11:16

you do not need to modify the make files if you are working with the existing FLOW-3D source files, which, I think, you are. Just modify the source and run make.

November 23, 2009, 03:11	general introduction for customizing flow3d with fortran routines	#1
jk75 New Member Johannes Köpf Join Date: May 2009 Location: Germany Posts: 29 Rep Power: 16	Hi all, I've read the manual chapters concerning customizing flow3d using fortran subroutines and became curious about the possibilities this customization might offer. But though I'm experienced in programming c++, I'm an absolute newbie to fortran. So I was wondering if there is somewhere a general introduction/tutorial/or something like that to help me understand what can be done by this customization (e.g. with variables are accessable,...) and how this is done (e.g. additional simple codes like those in the manual...). Many thanks in advance and best regards, Johannes

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Comparison between C/C++ and Fortran?	rick	Main CFD Forum	45	September 6, 2011 00:52
CFX11 + Fortran compiler ?	Mohan	CFX	20	March 30, 2011 18:56
User fortran routines, DEBUG AND OUTPUT	Bloshchitsyn Vladimir	CFX	5	October 29, 2007 01:31
call fortran routines from UDF	lily	FLUENT	0	March 29, 2005 18:26
General Introduction about STAR-CD wanted!	Jason	Siemens	3	February 16, 2000 07:07

November 29, 2009, 19:09		#2
MuxaB Senior Member michael barkhudarov Join Date: Mar 2009 Location: Sante Fe, New Mexico, USA Posts: 336 Rep Power: 18	Johannes, There is not much more written on this beyond what is described in the FLOW-3D manual and in the comments within the customizable subroutines and functions. It would be easier to first figure out what you are trying to achieve by customizing FLOW-3D to point you in the right direction. Michael

February 10, 2010, 16:18		#3
therockyy Member Yang Yue Join Date: Feb 2010 Location: Birmingham, UK Posts: 36 Rep Power: 16	Programming in Fortran is relative easy if you have background using C++. You can follow the manual to call the modules and include other variables. I think the most difficult question is how to link your customizations and make Flow-3D to response to them. You need to change the Makefiles.

May 22, 2012, 11:16		#5
MuxaB Senior Member michael barkhudarov Join Date: Mar 2009 Location: Sante Fe, New Mexico, USA Posts: 336 Rep Power: 18	you do not need to modify the make files if you are working with the existing FLOW-3D source files, which, I think, you are. Just modify the source and run make.