|
[Sponsors] |
October 4, 2004, 03:06 |
Boiling with fluent
|
#1 |
Guest
Posts: n/a
|
Dear Fluent Users,
I a new to Fluent and I am not aware of the capabilities of Fluent for calculating boiling flow. I have a problem similar to a pot boiling water. I would like to predict the amount of steam generated and the amount of droplets carried with the steam. I imagine this is difficult but any hints to capture global trends would be fruitfull. The most important aspect is to predict the water droplets. Thanks in advance Jan Rusås |
|
October 4, 2004, 08:13 |
Re: Boiling with fluent
|
#2 |
Guest
Posts: n/a
|
I have found the 2 tutorials Horizontal film boiling and Heat and mass transfer with the Mixture model. I will investigate the possibilities though those, but any comments,hints or experience is very welcome
|
|
May 23, 2011, 22:49 |
|
#3 |
New Member
Raúl
Join Date: Apr 2011
Posts: 3
Rep Power: 15 |
hi Jan
I'm trying to model evaporation but i haven't fount much information yet. My license has finished, so I don't have access to the fluent customer portal. Could you sent me those tutorials or any aditional information, my email es rlamadri@gmail.com. thanks Raúl |
|
June 18, 2011, 23:45 |
Boiling
|
#4 |
New Member
digvijay
Join Date: Feb 2011
Posts: 9
Rep Power: 15 |
Hi,
If you have "heat and mass transfer with mixture model tutorial and source.c udf file" please send me. Thank you. |
|
June 22, 2011, 12:47 |
|
#5 |
New Member
digvijay
Join Date: Feb 2011
Posts: 9
Rep Power: 15 |
Hi,
I have found the tutorial Heat and mass transfer with the Mixture model. If you have udf source.c file of above tutorial then please email me. My email id is digvijay8911@gmail.com. Thank You. |
|
September 9, 2012, 05:32 |
Help Needed
|
#6 |
New Member
STEPHEN BONG
Join Date: Jul 2012
Posts: 6
Rep Power: 13 |
Dear Jan,
Could you please forward a copy of your tutorial to me at stephenbongpy@gmail.com as I'm new to FLUENT and need it for my current project. Thanks a lot for your kind considerations and attention. Best Regards, Stephen |
|
September 9, 2012, 15:37 |
|
#7 |
New Member
samiullah
Join Date: Aug 2012
Posts: 21
Rep Power: 13 |
( i make the 2d model of shell and tube heat exchanger and mesh it but when select heat exchanger model in fluent it give error that primary and auxiliary regions are not overlapping ..... so plz help me what i do .... i'm new to use ansys
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
bubble diameter definition in multi phase flow boiling simulation FLUENT | Abishek | FLUENT | 13 | July 1, 2019 12:12 |
Two questions on Fluent UDF | Steven | Fluent UDF and Scheme Programming | 7 | March 23, 2018 03:22 |
How to open Icem mesh in Ansys Fluent? | emmkell | FLUENT | 27 | February 6, 2018 03:34 |
fluent parallel problem in win7 x64 system | dunga82 | FLUENT | 8 | April 19, 2012 20:23 |
Master node in parallel computing only distirubtion | syadgar | FLUENT | 1 | September 8, 2009 16:41 |