Measure the velocity in a line and time required travel from inlet to outlet (Ansys f

chun9321md · April 19, 2020, 10:49

Hi,

I wanted to measure the velocity in a line that slightly above the foil in 2D. How can i set that up in Ansys (version 2019 r3)? And how can i know the time required to travel from inlet to outlet?

Timothy

MKuhn · April 20, 2020, 02:13

Go to "Graphics and Animatrion" --> Mesh --> "New Surface" --> "Line/Rake" to define your desired line.

Go to "Results" --> "Graphics" --> "Particle Tracks"

vinerm · April 20, 2020, 05:34

Since airfoil has a curve, it would not be very easy to define the line. If you have equation of the airfoil, then you can use same equation to generate the points and import those in Fluent. Then plot velocity on these points. Other option is to use cell values, i.e., select the airfoil but export cell data. This would report velocities slightly above the airfoil as you need; points will automatically be half cell height away from the airfoil. Another option is to use wall shear stress. Since velocity at the wall is 0, velocity adjacent to the wall can be calculated; usually defined as shear velocity and determined using

$\sqrt{\frac{\tau_w}{\rho}}$

As far as residence time is concerned, you can plot streamlines with Time as variable. Do note that there is a range of time and not one value since not each flow parcel will reach the outlet in same time.

April 19, 2020, 10:49	Measure the velocity in a line and time required travel from inlet to outlet (Ansys f	#1
chun9321md New Member Tim Yick Join Date: Apr 2020 Posts: 3 Rep Power: 6	Hi, I wanted to measure the velocity in a line that slightly above the foil in 2D. How can i set that up in Ansys (version 2019 r3)? And how can i know the time required to travel from inlet to outlet? Timothy

April 20, 2020, 05:34	Line above airfoil	#3
vinerm Senior Member Vinerm Join Date: Jun 2009 Location: Nederland Posts: 2,946 Blog Entries: 1 Rep Power: 35	Since airfoil has a curve, it would not be very easy to define the line. If you have equation of the airfoil, then you can use same equation to generate the points and import those in Fluent. Then plot velocity on these points. Other option is to use cell values, i.e., select the airfoil but export cell data. This would report velocities slightly above the airfoil as you need; points will automatically be half cell height away from the airfoil. Another option is to use wall shear stress. Since velocity at the wall is 0, velocity adjacent to the wall can be calculated; usually defined as shear velocity and determined using $\sqrt{\frac{\tau_w}{\rho}}$ As far as residence time is concerned, you can plot streamlines with Time as variable. Do note that there is a range of time and not one value since not each flow parcel will reach the outlet in same time. __________________ Regards, Vinerm PM to be used if and only if you do not want something to be shared publicly. PM is considered to be of the least priority.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
bash script for pseudo-parallel usage of reconstructPar	kwardle	OpenFOAM Post-Processing	41	August 23, 2023 02:48
[Other] Contribution a new utility: refine wall layer mesh based on yPlus field	lakeat	OpenFOAM Community Contributions	58	December 23, 2021 02:36
[OpenFOAM] Annoying issue of automatic "Rescale to Data Range " with paraFoam/paraview 3.12	keepfit	ParaView	60	September 18, 2013 03:23
Regarding FoamX running Kindly help out	hariya03	OpenFOAM Pre-Processing	0	April 18, 2008 04:26
[blockMesh] Axisymmetrical mesh	Rasmus Gjesing (Gjesing)	OpenFOAM Meshing & Mesh Conversion	10	April 2, 2007 14:00

April 20, 2020, 02:13		#2
MKuhn Senior Member Moritz Kuhn Join Date: Apr 2010 Location: Germany, Dresden Posts: 207 Rep Power: 17	Go to "Graphics and Animatrion" --> Mesh --> "New Surface" --> "Line/Rake" to define your desired line. Go to "Results" --> "Graphics" --> "Particle Tracks"