|
[Sponsors] |
July 15, 2013, 20:42 |
how to set swirl number in ansys
|
#1 |
New Member
tamershahinreda
Join Date: Jul 2013
Posts: 4
Rep Power: 12 |
hello..
i want to simulate combustor chamber with air and fuel mass flow rate 1 litre and 0.5 litre respectively and axial velocity 0.5 m/s and swirl number - 0.066. but i dont know how and where i can insert the value of swirl number in the boundary condition.... if have any idea about this case help me please thanx ,,,,, |
|
July 16, 2013, 20:59 |
|
#4 |
New Member
tamershahinreda
Join Date: Jul 2013
Posts: 4
Rep Power: 12 |
ghazlani iam not asking about meshing please
iam asking about "'SWIRL NUMBER INSERTING IN ANSYS'" if you can give me some tutorial about it i will be very thanx regards |
|
July 16, 2013, 21:57 |
|
#5 |
Senior Member
|
That is part of his signature rather than response. As I said before, you need to decide what kind of vortex could be representative for you inlet. Then you can calculate the parameters according to the swirl number. You can search with the term "Batchelor vortex" for an example. However as I recalled the axial velocity is not be uniform so that the mass flux rather than the axial velocity distribution will be guaranteed.
|
|
July 16, 2013, 22:29 |
|
#6 |
New Member
tamershahinreda
Join Date: Jul 2013
Posts: 4
Rep Power: 12 |
thank you black smak
let us suggest situations like (vortex) and suggest numbers and if we divide tangential velocity by axial and equal it with swirl number to find tangential velocity ..... please make numbers and let it very clear please it still very very vague.. Regards.... |
|
July 16, 2013, 22:50 |
|
#7 |
Senior Member
|
Let the axial and tangential velocity of some axisymmetric vortex be U(r; a) and V(r; q), where a and q are the parameters to be determined. Then the mass flux
MF = Integrate[U(r;a), {r, 0, R}] = f(a) and the swirl number SN=Weighted Integral of V(r;a) / Weighted Integral of U(r;a) = g(a, q) can be calculated. Then a and q can be determined for a given mass flux and swirl number so are the velocity profiles for you inlet boundary condition. |
|
July 17, 2013, 00:36 |
|
#8 |
New Member
tamershahinreda
Join Date: Jul 2013
Posts: 4
Rep Power: 12 |
To be honsety with you i can't understand you very well
It seems that you have good idea about this (Inserting Swirl Number in Ansys) Many people want to know how to do it..........many questions .... Please if you can make an example...to explain how to put swirl number in ansys. help us please In the example clarify fuel and air inlet mass flow rate and swirl number and ... and ... you can assume it .... and step by step make the calculation and let us know how you can put the swirl number value in ansys pictures very usefull if you can upload it... thank you very |
|
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Pro/E to ANSYS Parameterization Guide | Trues | ANSYS | 4 | April 18, 2018 06:52 |
[snappyHexMesh] No layers in a small gap | bobburnquist | OpenFOAM Meshing & Mesh Conversion | 6 | August 26, 2015 10:38 |
DecomposePar unequal number of shared faces | maka | OpenFOAM Pre-Processing | 6 | August 12, 2010 10:01 |
air bubble is disappear increasing time using vof | xujjun | CFX | 9 | June 9, 2009 08:59 |
[blockMesh] BlockMeshmergePatchPairs | hjasak | OpenFOAM Meshing & Mesh Conversion | 11 | August 15, 2008 08:36 |