CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > Software User Forums > ANSYS > FLUENT

natural convection in a square enclosure with a partial dividing wall

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
Old   April 30, 2000, 01:27
Default natural convection in a square enclosure with a partial dividing wall
  #1
sandeepmishra
Guest
 
Posts: n/a
Hi, I want to model natural convection processes inside a square enclosure(two dimensional) with a partial wall inside it attached to one of the edges and vertical. Now when i mesh the geometry and solve the partial dividing wall is not considered and the flow is seen ACROSS the wall, while actually the flow should change direction at the wall obstacle. I am new to CFD and fluent and would appreciate help in how to go about doing it. Any other considerations which should be kept in mind for such problems??? Thanks for the help. sandeep
  Reply With Quote

Old   May 3, 2000, 07:17
Default Re: natural convection in a square enclosure with a partial dividing wall
  #2
Jin-Wook LEE
Guest
 
Posts: n/a
Dear Sandeepmishra

It is no problem to construct dividing wall inside the cavity. if you do not assign the inner dividing wall as 'WALL', then Gambit consider it as 'INTERIOR', resulting in cross flow over the dividing wall. Check your dividing wall is considered as really 'WALL' by Gambit and by Fluent. Just before, I have tested your case, and I had no problem expect fairly difficult convergence. It takes only 10 minutes by my P-III PC.

Your case is very simple one, so that you should have good results. Good luck with you.

Recommendation : If you have both of Fluent 4.x and 5.x, I recommend that Fluent 4.x rather than 5.x for natiral convection problem. Convergence is very good by using 4.x.

Sincerely, Jinwook
  Reply With Quote

Old   May 3, 2000, 12:04
Default Re: natural convection in a square enclosure with a partial dividing wall
  #3
sandeepmishra
Guest
 
Posts: n/a
Thanks ginwook, I will definitely give it a try by the way you suggested. Thanks again. sandeep
  Reply With Quote

Old   May 6, 2000, 05:25
Default Re: natural convection in a square enclosure with a partial dividing wall
  #4
Venkata Krishnan
Guest
 
Posts: n/a
Dear Sandeepmishra ,

I have done some work in this area . There are a two of options available for your problem.

1. If you want to model the wall as conducting then follow Jin-wook's suggestion.

2. If you want to model the wall as adaibatic it is better to model just the fluid domain and leave the partition as empty.

The default BC at the domain bounadry i.e

adiabatic wall, will ensure that no flow occurs at the region.

Other suggestion -

Bias the mesh near all the walls

Use correct Boussinesq inputs to achieve quicker

convergence.
  Reply With Quote

Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Natural Convection BC yipseng FLUENT 9 February 4, 2010 00:46
Natural Convection BC yipseng Main CFD Forum 1 January 20, 2010 21:54
Errors running allwmake in OpenFOAM141dev with WM_COMPILE_OPTION%3ddebug unoder OpenFOAM Installation 11 January 30, 2008 21:30
Meshing a natural convection problem sandeepmishra FLUENT 1 May 31, 2000 15:36
natural convection in a square enclosure with a partial dividing wall sandeep Main CFD Forum 0 April 30, 2000 01:38


All times are GMT -4. The time now is 11:23.