CFD Online Discussion Forums

CFD Online Discussion Forums (http://www.cfd-online.com/Forums/)
-   FLUENT (http://www.cfd-online.com/Forums/fluent/)
-   -   2D, Can't Display Filled Contours. (http://www.cfd-online.com/Forums/fluent/40576-2d-cant-display-filled-contours.html)

David April 14, 2006 06:58

2D, Can't Display Filled Contours.
 
Hi,

I have a number of 2D cases where I can't display filled contours. Instead I just get the grid with colour gradients imposed on the lines.

I have seen this message befor, although have had no joy with disabling hardware acceleration as was recommended.

Any suggestions.

Thanks

David

Chandra Murthy April 14, 2006 08:07

Re: 2D, Can't Display Filled Contours.
 
while plotting don't select any boudary entities in the list, just press plot button.

David April 14, 2006 10:01

Re: 2D, Can't Display Filled Contours.
 
Genius! Thank you.

David

eslamian September 20, 2012 16:56

2D, Can't Display Filled Contours
 
I have the same problem, i.e. in 2D I cannot show the filled contours instead I get grids. I did not undrestand the answer.

It is in the contour section not plot. Any suggestions? I am stuck.

Thanks
Morteza

syavash September 20, 2012 20:12

Quote:

Originally Posted by eslamian (Post 382853)
I have the same problem, i.e. in 2D I cannot show the filled contours instead I get grids. I did not undrestand the answer.

It is in the contour section not plot. Any suggestions? I am stuck.

Thanks
Morteza


Be sure that no boundaries in the "Surfaces" list be selected in Contour window.

Bests.

eslamian September 21, 2012 10:42

Thanks Syavash. I got it. It worked as you suggested.

mashiro September 24, 2012 04:21

Can you help me?

I can not write Cd multi line when I run parallell and chose time "transient".

It's show

""Drag Convergence"
"Flow Time" "Cd"
3.87500e-02 1.61505e+03
"

when I chose time"steady"

"Drag Convergence"
"Flow Time" "Cd"
1.00000e-02 1.09653e+02
2.00000e-02 -5.27841e+00
3.00000e-02 -4.84571e+01
4.00000e-02 -6.28311e+01
5.00000e-02 -1.34413e+02
6.00000e-02 -2.63939e+02
"

I need to write in Cd file same steady. Thank you.

HariCharan April 21, 2016 05:59

Thanks very much Chandrakanth. It worked

jingl1 May 15, 2016 16:46

Hi, syavash, I have the same question that the 2D contour can't be shown, while I just got the grid. I am pretty sure that no boundaries in the "Surfaces"
list be selected in Contour window. Can you help me? Thank you very much.
Quote:

Originally Posted by syavash (Post 382887)
Be sure that no boundaries in the "Surfaces" list be selected in Contour window.

Bests.


syavash May 16, 2016 12:37

Quote:

Originally Posted by jingl1 (Post 600157)
Hi, syavash, I have the same question that the 2D contour can't be shown, while I just got the grid. I am pretty sure that no boundaries in the "Surfaces"
list be selected in Contour window. Can you help me? Thank you very much.

Hi,

Can you post a picture of what you get from Contour panel?!


All times are GMT -4. The time now is 15:46.