CFD Online Logo CFD Online URL
www.cfd-online.com
[Sponsors]
Home > Forums > FLUENT

3D mesh around a wing using gambit

Register Blogs Members List Search Today's Posts Mark Forums Read

Reply
 
LinkBack Thread Tools Display Modes
Old   May 15, 2006, 11:51
Default 3D mesh around a wing using gambit
  #1
M. ssuri
Guest
 
Posts: n/a
I am using Gambit for creating 3Dmesh round a wing , I need a help for creating this mesh . I tried to mesh edges, faces and then volumes. This method worked for volumes which does not contain wing. for the volume which contains wing this method fails...Why???!!!

Can any one send me a steps or advise?

Greast Thanks
  Reply With Quote

Old   May 15, 2006, 13:55
Default Re: 3D mesh around a wing using gambit
  #2
anindya
Guest
 
Posts: n/a
There is a gambit tutorial for meshing an airplane geometry (half section). Maybe that will help you.
  Reply With Quote

Old   May 16, 2006, 02:06
Default Re: 3D mesh around a wing using gambit
  #3
dongtao
Guest
 
Posts: n/a
where is the tutorial file?In the standard gambit help file, I cann't find any tutorial file about meshing an airplane. could you sent this file to my email:dongtaomail@gmail.com, thanks in advance.
  Reply With Quote

Old   May 16, 2006, 13:44
Default Re: 3D mesh around a wing using gambit
  #4
Anindya
Guest
 
Posts: n/a
Find the tutorial guide here.

http://www.wka.tu-harburg.de/intra/d...df/tg/tg14.pdf

Anindya
  Reply With Quote

Old   May 17, 2006, 11:42
Default Re: 3D mesh around a wing using gambit
  #5
M. ssuri
Guest
 
Posts: n/a
Thanks Anindya,,, This will help me

M. Essuri
  Reply With Quote

Old   May 25, 2006, 02:44
Default Re: 3D mesh around a wing using gambit
  #6
QuynhGiao
Guest
 
Posts: n/a
you can use triangle to mesh all the face of volume.Note:divide many vertices on leading edge and trailing edge of the wing.then, you can use Tgrid to smooth the mesh.You can email to me ro have more info.I am going to graduate from Univesity and my thesis is "Flow over an 3D airfoil using gambit and fluent..""
  Reply With Quote

Old   June 6, 2006, 10:38
Default Re: 3D mesh around a wing using gambit
  #7
QGiao
Guest
 
Posts: n/a
Dear aerosapce_iist@yahoo.com, I can't email to u. You can mesh your foil in gambit and then u use fluent, set the condition in fluent e.g. define model(solver,viscous,..).In gambit, u set the bounary condition for faces(velocity inlet, pressure outlet, symetry, ..) to set the value of boundary condition to solve...The residual u use in Fluent is about 1e-5. after about 2500 iteration, the solution converges anh u will have the pressure.I send u apic of wing that I have done.hope that I will help u.
  Reply With Quote

Old   June 6, 2006, 10:39
Default aerosapce_iist *NM*
  #8
QGiao
Guest
 
Posts: n/a
  Reply With Quote

Old   April 30, 2009, 14:05
Default
  #9
New Member
 
Kartik
Join Date: Apr 2009
Posts: 4
Rep Power: 8
kartikkp is on a distinguished road
Quote:
Originally Posted by QuynhGiao
;132543
you can use triangle to mesh all the face of volume.Note:divide many vertices on leading edge and trailing edge of the wing.then, you can use Tgrid to smooth the mesh.You can email to me ro have more info.I am going to graduate from Univesity and my thesis is "Flow over an 3D airfoil using gambit and fluent..""

Hi
i would be glad to see you work. i am looking to work on same lines.

my email id is kkadakia2009@gmail.com

regards
kartik
kartikkp is offline   Reply With Quote

Old   April 30, 2009, 15:06
Smile Hii
  #10
Member
 
ANIL
Join Date: Apr 2009
Posts: 35
Rep Power: 8
makaero is on a distinguished road
@@: QuynhGiao
Guest

I am working on" Flow over 3d wing with sinusoidal leading edge", but i coudnt get a good volume mesh in Gambit because of sharp trailing edge...
In next attemp, i joined the last two points of airfoil with straight line, but the 3d Boundary layer resulted in highly skewed elements.

I wud be glad to see your work, it might help me...looking forward to hear from you.
email: anilsmailaero@gmail.com

Thank you.
makaero is offline   Reply With Quote

Old   July 21, 2010, 02:04
Default
  #11
Member
 
nguyen van trieu
Join Date: Jul 2009
Posts: 69
Rep Power: 8
nvtrieu is on a distinguished road
Hello Quynh Giao,

Today, I've just found your post here. It was posted over 4 years ago. However I hope you still work with CFD now! ^_^. Therefore, I would ask your email to discuss with you about this topic.
Thanks you so much!

Nguyen Van Trieu.
Email: trieuckgt@gmail.com
nvtrieu is offline   Reply With Quote

Old   February 9, 2012, 17:49
Default
  #12
New Member
 
Amr Ahmed Ahmed El feky
Join Date: Jan 2012
Posts: 1
Rep Power: 0
mero_magiver is on a distinguished road
Sorry i have the same problem . I am using Gambit for creating 3Dmesh round a wing , I need a help for creating this mesh . I tried to mesh edges, faces and then volumes. This method worked for volumes which does not contain wing. for the volume which contains wing this method fails..
The link of tutorial
http://www.wka.tu-harburg.de/intra/d...............is not working
mero_magiver is offline   Reply With Quote

Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Converting Fluent mesh files to Gambit neutral files samuelkc ANSYS Meshing & Geometry 5 July 24, 2013 08:02
[ICEM] Structured Mesh 3D Wing Tip Michiel ANSYS Meshing & Geometry 5 October 21, 2010 08:39
fluent add additional zones for the mesh file SSL FLUENT 2 January 26, 2008 12:55
Mesh Resolution in Gambit Vidya Raja FLUENT 2 January 19, 2006 00:35
3-D Mesh Check in Gambit..... SHR FLUENT 4 March 25, 2003 04:10


All times are GMT -4. The time now is 14:44.