DPM report sample in batch mode

October 31, 2006, 09:00

Dear users, how can i perform DPM sample trajectories in batch mode by *.jou file?

Using GUI i can do *Report/Discrete Phase/Sample... *select my injections and plane* *hit compute*

I`m using 6.2.16 version. I tried commands like report/dpm-sample-report or (ti-dpm-sample-report) but they does not works...

Thanx very much for Your answers Milano

Bernhard · September 29, 2009, 05:25

Are there any solutions known for this issue? Particle sampling in the planes works properly for me in the graphical mode, but when I try to configure this using the TUI in a journalfile, the corresponding files are created, but the particle data is not sampled.

barzin · August 6, 2012, 12:00

Dear Bernhard

Hope you are well. I know it has been a long time from this post but now I have faced kinda same problem. I would like to the changes of my particle variables (e.g. velocity magnitude or diameter) in a specific plane which I define. Could this be done by using sampling? It does not work for me at all when I follow the Fluent user guid. Please help me if you can.
Bests
Barzin

Bernhard · August 6, 2012, 16:01

It is a long time ago that I worked with Fluent, but probably I solved it. I found this in an old journalfile (Fluent 6)

Code:

/define/models/dpm/user-defined

That is the best I can do for you. Good luck!

October 31, 2006, 09:00	DPM report sample in batch mode	#1
Milano Guest Posts: n/a	Dear users, how can i perform DPM sample trajectories in batch mode by .jou file? Using GUI i can do Report/Discrete Phase/Sample... select my injections and plane hit compute I`m using 6.2.16 version. I tried commands like report/dpm-sample-report or (ti-dpm-sample-report) but they does not works... Thanx very much for Your answers Milano

August 6, 2012, 16:01		#4
Bernhard Senior Member Bernhard Join Date: Sep 2009 Location: Delft Posts: 513 Rep Power: 9	It is a long time ago that I worked with Fluent, but probably I solved it. I found this in an old journalfile (Fluent 6) Code: /define/models/dpm/user-defined That is the best I can do for you. Good luck!

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
to run a replayfile in batch mode from UNIX	froztbear	ANSYS Meshing & Geometry	3	October 18, 2011 05:11
Running Ansys in BAtch Mode	kuleuvenstudent	ANSYS	0	November 5, 2010 13:27
DPM model in parallel batch mode	Prashanth	FLUENT	2	March 6, 2009 07:54
DPM postprocessing in Batch mode	Abigail	FLUENT	1	June 4, 2007 08:11
DPM in Batch Mode	MM	FLUENT	0	December 15, 2006 13:17

September 29, 2009, 05:25		#2
Bernhard Senior Member Bernhard Join Date: Sep 2009 Location: Delft Posts: 513 Rep Power: 9	Are there any solutions known for this issue? Particle sampling in the planes works properly for me in the graphical mode, but when I try to configure this using the TUI in a journalfile, the corresponding files are created, but the particle data is not sampled.

August 6, 2012, 12:00		#3
barzin Member barzin Join Date: Jan 2011 Posts: 33 Rep Power: 4	Dear Bernhard Hope you are well. I know it has been a long time from this post but now I have faced kinda same problem. I would like to the changes of my particle variables (e.g. velocity magnitude or diameter) in a specific plane which I define. Could this be done by using sampling? It does not work for me at all when I follow the Fluent user guid. Please help me if you can. Bests Barzin