How to Plot Graph in Fluent ?
1. How to plot graph of "Pressure vs Time" in Fluent?
In XY plot, I could not find any "Time" function in X-Axis Function. 2. How to plot "Viscosity vs Time" & "Shear Rate vs Time" graph in Fluent? I could not find the "Viscosity,Shear Rate & Filled Volume" in Y-Axis function. Please help me. |
Re: How to Plot Graph in Fluent ?
Did you do unsteady (transient) simulations?
Also then these plots can only be done using monitors. |
Re: How to Plot Graph in Fluent ?
Yes, unsteady simulation.
You mean setting at Monitor, and get the graph during simulation?? |
Re: How to Plot Graph in Fluent ?
Correct - otherwise you have to use your saved files, load all of them using a script and process them, writing the results to files which you can combine.
|
Hi, I'm working in cyclone simulation. I want to know How to plot graph of
1."Aerodynamic Diameter Vs Collection Efficiency" in Fluent? 2."Aerodynamic Diameter Vs Fraction of Total Amount Deposited" in Fluent? 3."Normalized Particle Diameter Vs Collection Efficiency" in Fluent? I really need to sought out these problems. |
Hi antara,
I am also working on gas cyclone. Why exactly do you need to go for Aerodynamic Diameter Vs Collection Efficiency, Aerodynamic Diameter Vs Fraction of Total Amount Deposited, and Normalized Particle Diameter Vs Collection Efficiency? Cyclones are characterized in terms of cut-off diameters, and I think you should go with that. |
Thanks for your reply. I needed this graph to know the collection efficiency in tubes, internal loss and also penetration efficiency. But I could not plot those graphs.Do I need to plot these on matlab? Or can I use fluent for this??
|
Hi,
I need to plot a transient case of temperature against time plot. I have did an autosave during the the simulation. Previously, I have used monitor and I have the graph plotted from using average vertex. After closing Fluent, I cannot seem to retrieve the graph plotted. Could anyone assist in this? Thank you very much for your time in advance. |
Hi,
Usually a plot is saved in a *.out format. Search for *.out in your fluent or project path and you should find your file. - If you still can't find it take a look on your monitor settings and enable the writh plot field... |
Quote:
I usually write up a python script to generate the journal file for fluent then just run the journal file in fluent. |
Thank you so much for the reply.
I understand what you all have suggested. I would like to ask if i need to compile all the data using script (udf), may i ask how should i go about writing the script? Thank you so much in advance. |
In my opinion a UDF need to to compiled in every case. Is this a general question or does your script mean an special case? When you saw writing scribt, is this about an UDF or about the plot export you asked in the last post?
Generall: There is a UDF Guide on the fluent homepage (customer portal) this is a good hint for a lot of applications. |
Thank you for the haste reply.
I am only referring to a general case as of how to write the udf script to plot the time dependent graph using data files saved during the run. Thank you for your time. |
Hi,
I have the same problem as Jane, I still could not understand on how to plot "Pressure vs Time" in FLUENT. I really appreciate who can explain in details. Thanks |
Before running your simulation, go to monitors > volume monitors or surface monitors > set up a monitor point on the desired location > make sure you select "write to file" and set the desired axis values (iterations, time-steps or flow-time).
Volume monitors should be used if you want to know your value in a whole domain, or a part of the domain volume; so for pressure: if you want to know the average value over the whole domain. Surface monitors should be used if you want to know the value on a plane, line or point. For pressure, you may want to know the surface-average value on a wall, or for a point, the vertex-average value. For this, you need to set up a new surface > point and enter the desired coordinates. |
Thanks to CeesH,
After closing FLUENT, I cannot retrieve the saved file. May you assist in this? Thanks for your time |
Hi, I have one question regarding to contour. How to figure out the development of pressure contours at different times in transient simulation?
Thank you |
Plot monitor files by Fluent?
Hello,
I am wondering how to plot my variables in Fluent. I have created a surface monitor for a point in my transient calculation(suppose velocity versus time). I save the monitor file. I want to know a way how I can directly plot that .out file in Fluent . I can open .out file, but need to open it in notepad first and remove the header and then open it by Excel which can be time consuming if you have many surface monitor files. I am looking for a fast way. any idea? Thank you in advance! |
2 Attachment(s)
[QUOTE=CeesH;531740]
Thank you for your reply. I am beginner in Ansys.and working on pulsatile blood flow through artery.now i want to draw velocity vs time graph at different position of artery In Ansys fluent.How can i draw it in CFD post?Or is there any other way? |
Shorab,
I do not use CFD post. I use Tecplot 360 to post-process my data. I believe those figures you shared, are prepared by Tecplot. Best of Luck |
I am also trying to attain a pressure vs time graph however when i follow CeesH's steps and try to make the point surface in fluent the following error comes up.
Error: Surface creation failed! Error Object: #f I'm new to fluent can someone please tell me how to resolve this issue Thanks in advance |
I am also trying to attain a pressure vs time graph however when i follow CeesH's steps and try to make the point surface in fluent the following error comes up.
Error: Surface creation failed! Error Object: #f I'm new to fluent can someone please tell me how to resolve this issue Thanks in advance |
i need more answer on how to plot pressure time graph in fluent
Quote:
Please i will appreciate if you will make it more elaborate to me on how to plot a graph of pressure against time. Am working on flow around high speed train in transient steady using inviscid solver. Thanks for your human kindness. |
how can i plot veloocity vs time?
please help me |
Quote:
how can i plot veloocity vs time? please help me |
how can i plot veloocity vs time?
please help me |
Describe your problem better!
If you are using a steady state model, there is no time. If you are using a transient model, simply go to "Graphics" and plot your simulation for a specific time. If you wanna plot one variable as a function of time (which I think you want) you have 3 ways: 1- save the cas/dat file every time step( or every 2,3,...) and then open them via another program like Tecplot 2-You can set up an animation BEFORE running your transient simulation via "solution animations" 3- You can also save your data (variable and time step) via a ".out" file in "surface monitors" and then open it in Excel Good luck, Hooman |
Quote:
hello thanks for your reply can you explain third number more( step by step ). because in surface monitor i cant have exact velocity in report type.I have average or max ,.... |
It depends on the type of information you would like to have, velocity of a point, average velocity on a line or a surface...based on that, choose the appropriate type ( like vertex average or area-weighted), select the point or surface or area,... and then run your simulation...for the detailed information, you need to read the Ansys Fluent Theory Guide ...
Good luck, H |
reply
Quote:
excuse me |
transient simulations
i hAve don transient simulations for 3 minutes and i have set monitors ,can i get concentration versus time graph in post processing? thanks in advance for help
|
All times are GMT -4. The time now is 21:15. |