How to set up this kind of boundary condition?

November 23, 2008, 10:02

Hi, everyone. I am using a UDS to modeling the mass transport beween two zones. After the mesh file was read into FLUENT, the common boundary between two zones is auto-transformed into two WALL type boundaries, the name of one is WALL and the other is WAlL_SHADOW. However, on the common boundary, what we know only is that the specified flux of uds is equal but the magnitude of flux is unknown. How to set up this kind of boundary condition?

Thanking you in anticipation.

John

November 23, 2008, 11:57

Look these tutorials:

http://rapidshare.de/files/40976967/TG.rar.html

November 23, 2008, 13:46

I forgot the meshes and their respectively tutorials of each part: Here there are:

File TUTFILES.rar (89155 KB):

http://rapidshare.de/files/40977811/TUTFILES.rar.html

November 24, 2008, 07:54

Hi, Rogerio. Thank you for your reply. However, it is a pity that I cannot free-download your files due to a unknown reason, though the prompt say the file is inexistence. So, could you give me the other link for these files?

BG

John

November 24, 2008, 07:57

http://www.4shared.com/dir/8279926/7..._ICEM_etc.html

November 23, 2008, 10:02	How to set up this kind of boundary condition?	#1
John Guest Posts: n/a	Hi, everyone. I am using a UDS to modeling the mass transport beween two zones. After the mesh file was read into FLUENT, the common boundary between two zones is auto-transformed into two WALL type boundaries, the name of one is WALL and the other is WAlL_SHADOW. However, on the common boundary, what we know only is that the specified flux of uds is equal but the magnitude of flux is unknown. How to set up this kind of boundary condition? Thanking you in anticipation. John

November 23, 2008, 11:57	Re: How to set up this kind of boundary condition?	#2
Rogerio Fernandes Brito Guest Posts: n/a	Look these tutorials: http://rapidshare.de/files/40976967/TG.rar.html

November 23, 2008, 13:46	Re: How to set up this kind of boundary condition?	#3
Rogerio Fernandes Brito Guest Posts: n/a	I forgot the meshes and their respectively tutorials of each part: Here there are: File TUTFILES.rar (89155 KB): http://rapidshare.de/files/40977811/TUTFILES.rar.html

November 24, 2008, 07:54	Re: How to set up this kind of boundary condition?	#4
John Guest Posts: n/a	Hi, Rogerio. Thank you for your reply. However, it is a pity that I cannot free-download your files due to a unknown reason, though the prompt say the file is inexistence. So, could you give me the other link for these files? BG John

November 24, 2008, 07:57	Re: How to set up this kind of boundary condition?	#5
Rogerio Fernandes Brito Guest Posts: n/a	http://www.4shared.com/dir/8279926/7..._ICEM_etc.html

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
UDF for 3rd Kind Boundary Condition	Ismail	FLUENT	2	October 26, 2015 01:57
Kind Attention	ajayrac	FLUENT	0	March 22, 2008 01:21
What kind of boundary?	Nico	FLUENT	1	November 16, 2006 23:37
Boundary condition of the third kind or Danckwertz boundary condition	plage	OpenFOAM Running, Solving & CFD	4	October 3, 2006 12:21
Slip Boundary Condition for Moving Boundary	Shukla	Main CFD Forum	3	November 11, 2005 15:02